def main():
try:
# Set Global Watchdog timeout in Seconds
MOD.watchdogEnable(300)
res = JANUS_SER.init("115200",'8N1')
if (res == -1):
return
#Set Network specific settings
res = NETWORK.initGsmNetwork(myApp.NETWORK,myApp.BAND)
if (res == -1):
return
#Init GPRS
GPRS.init('1',myApp.APN)
#Inform Application that a Data Connection is not available
JANUS_SER.set_DCD(0)
# Loop forever, without this loop the script would run once and exit script mode. On reboot or power-on the script would run once more
while (1):
MOD.watchdogReset()
#Wait until module is registered to GSM Network
res = NETWORK.isGsmRegistered(180) #Wait 180 seconds for module to obtain GSM registration
if (res == -1):
return
#Wait until module is attached to GPRS
res = NETWORK.isGprsAttached(180) #Wait 180 seconds for module to obtain GPRS Attachment
if (res == -1):
return
#############################################################################################################################
## Opening Socket Connection to Server
#############################################################################################################################
res = GPRS.openSocket(myApp.IP,myApp.PORT,1,myApp.USERNAME,myApp.PASSWORD,myApp.PROTOCOL,0)
#Inform Application that a Data Connection is not available
DCD = MDM.getDCD()
if (DCD == 1):
JANUS_SER.set_DCD(1)
#Forward CONNECT Message to Serial Port
JANUS_SER.sendUART('\r\nCONNECT\r\n')
##Loop while Socket connected
while(1):
MOD.watchdogReset()
#Forward serial port data to socket connection
DCD = MDM.getDCD()
if (DCD == 1):
#Get data from serial port
res = JANUS_SER.readUART()
if (len(res)!=0):
#Forward data to open socket
res = MDM.send(res,1)
#Forward socket data to serial port
DCD = MDM.getDCD()
if (DCD == 1):
#Get data from open socket connection
res = MDM.receive(1)
if (len(res)!=0):
#Forward socket data to serial port
JANUS_SER.sendUART(res)
#When socket is closed exit loop via this path
#Will guarantee that '\r\nNO CARRIER\r\n' is sent every time
DCD = MDM.getDCD()
if (DCD == 0):
#Inform Application that a Data Connection is not available
JANUS_SER.set_DCD(0)
ATC.delaySec(1)
#Get any remaining data from closed socket connection
res = MDM.receive(1)
if (len(res)!=0):
#Forward socket data to serial port
JANUS_SER.sendUART(res)
break
except:
print "Script encountered an exception"
print "Exception Type: " + str(sys.exc_type)
print "MODULE -> TerminusS2E"
return
def main():
try:
# Set Global Watchdog timeout in Seconds
MOD.watchdogEnable(300)
#Initialize the serial interface @ 115200, we must do this or nothing comes out the serial port
res = JANUS_SER.init("115200",'8N1')
if (res == -1):
return
JANUS_SER.sendUART("Beginning the Terminus Tracker Demo Program. \r\n\r\n")
#Initialize the configuration, returns 0 for defaults, 1 for normal.
ConfigLoad = JANUS_CONFIG.init()
#Transpose the configuration list to myApp for usage here
#We transpose only the main Config class to handle updates
if (ConfigLoad == 0):
myApp = JANUS_CONFIG.Config
JANUS_SER.sendUART("Defaults Loaded.\r\n")
elif (ConfigLoad == 1):
myApp = JANUS_CONFIG.Config
JANUS_SER.sendUART("Configuration File Loaded.\r\n")
else:
myApp = JANUS_CONFIG.Config
JANUS_SER.sendUART("Configuration ERROR. Defaults Loaded.\r\n")
#Initialize the I/O, turn on the stat LED
res = JANUS_IO.init(myApp.SLED)
if (res == -1):
return
#Read if Auto-On is active or not, 1 is active, 0 is inactive.
res = JANUS_IO.AutoONControl('READ', myApp.AUTOON)
JANUS_SER.sendUART("\r\nAuto On: " + myApp.AUTOON + "\r\n")
#If Auto-on is OFF and we want it ON, set it.
if (res == 0 and myApp.AUTOON == 'ON'):
res = JANUS_IO.AutoONControl('SET', myApp.AUTOON)
if (res == -1):
return #Errored out
elif (res == -2):
JANUS_SER.sendUART("Timed out while waiting for MCU response. \r\n")
elif (res == 1):
JANUS_SER.sendUART("Auto ON Enabled. \r\n")
#If Auto-on is ON and we want it OFF, set it.
if (res == 1 and myApp.AUTOON == 'OFF'):
res = JANUS_IO.AutoONControl('SET', myApp.AUTOON)
if (res == -1):
return #Errored out
elif (res == -2):
JANUS_SER.sendUART("Timed out while waiting for MCU response. \r\n")
elif (res == 0):
JANUS_SER.sendUART("Auto ON Disabled. \r\n")
#If Auto-on is OFF, and we have it set as OFF. Let's see what caused this wake up and report it.
#Although we can read IGN/SW directly, we check the MCU instead because they
#May not be active as this point even though the MCU caught it.
WakeupCause = ''
if (res == 0 and myApp.AUTOON == 'OFF'):
res = JANUS_IO.SW_IGN_Status()
if (res == -1):
return #Errored out
elif (res == 0):
JANUS_SER.sendUART("Wake up cause: N/O Switch \r\n")
WakeupCause = 'Switch'
elif (res == 1):
JANUS_SER.sendUART("Wake up cause: Ignition \r\n")
WakeupCause = 'Ignition'
elif (res == 2):
JANUS_SER.sendUART("Wake up cause: Both the Ignition and N/O Switch \r\n")
WakeupCause = 'Both'
elif (res == -2):
JANUS_SER.sendUART("Wake up cause: Unknown \r\n")
WakeupCause = 'Unknown'
JANUS_SER.sendUART("\r\nInitializing Module GPRS. \r\n")
#Set Network specific settings, wait for SIM card to be ready
res = NETWORK.initGsmNetwork(myApp.NETWORK,myApp.BAND)
if (res == -1):
return
#Init GPRS
GPRS.init('1',myApp.APN)
JANUS_SER.sendUART("GPRS Initialized. \r\n")
################################################################
#### BEGIN Newly Added Config Stuff
################################################################
#Initalize GPS
JANUS_SER.sendUART("\r\nInitializing Module GPS. \r\n")
res = JANUS_GPS.init(myApp.LNA)
if (res != 0):
JANUS_SER.sendUART("Failed to Initialize GPS, ERROR: " + res + "\r\n\r\n")
return
JANUS_SER.sendUART("GPS Initialized. \r\n\r\n")
#Setup SMS
if (myApp.SMS_ENABLED == 'TRUE'):
JANUS_SER.sendUART("SMS Enabled, Initializing. \r\n")
JANUS_SMS.configSMS()
JANUS_SER.sendUART("SMS Initialized. \r\n\r\n")
################################################################
#### END Newly Added Config Stuff
################################################################
# Loop forever, without this loop the script would run once and exit script mode. On reboot or power-on the script would run once more
while (1):
MOD.watchdogReset()
JANUS_SER.sendUART("Registering Module. \r\n")
#Wait until module is registered to GSM Network
res = NETWORK.isGsmRegistered(180) #Wait 180 seconds for module to obtain GSM registration
if (res == -1):
return
#Wait until module is attached to GPRS
res = NETWORK.isGprsAttached(180) #Wait 180 seconds for module to obtain GPRS Attachment
if (res == -1):
return
JANUS_SER.sendUART("Module Registered Successfully. \r\n\r\n")
#############################################################################################################################
## Opening Socket Connection to Server
## We are opening in Command Mode to have the best control
#############################################################################################################################
#Update Unit information
res = ATC.getUnitInfo()
# Start timeout timer
timerB = timers.timer(0)
timerB.start(int(myApp.INTERVAL))
SwitchPos = 'Open' #Default State for Switch
IgnPos = 'Inactive' #Default State for Switch
FirstTimeThrough = 'TRUE' #Initialize flag for the first time running the connection/loop
SENDSTRING = [] #Initialize the string list being sent to the server
StringCount = 0
# Loop forever, without this loop the script would run once and exit script mode. On reboot or power-on the script would run once more
while (1):
while (1):
MOD.watchdogReset()
#Update NMEA Data
#The following are available through the included GPS module:
#GPS.getActualPosition(), returns all fields like AT$GPSACP would
#GPS.getLastGGA()
#GPS.getLastGLL()
#GPS.getLastGSA()
#GPS.getLastGSV()
#GPS.getLastRMC()
#GPS.getLastVTG()
#GPS.getPosition(), this gives LAT/LONG in numeric format
#For the purposes of this demo, RMC will be used
#The returned value gives a \r\n at the end so we must strip it for proper usage.
GPSPositionTemp = ''
GPSPositionTemp = GPS.getLastRMC()
GPSPositionTemp = GPSPositionTemp.rstrip()
#Update switch and ignition information
#We simply clear after the report is sent, so by default it's sent as Open/Inactive until it's read as the opposite.
#We're polling the MCU signals and then signaling back "we got the information" so we only read once, giving us one or both events to report
# 0: Pass, Switch is triggered
# 1: Pass, Ignition is triggered
# 2: Pass, BOTH are triggered
# -1: Exception
# -2: Pass, Neither is triggered
EventCheck = JANUS_IO.SW_IGN_Status()
if (EventCheck == 0): #Switch has been triggered
SwitchPos = 'Closed'
#JANUS_SER.sendUART("SwitchPos : " + SwitchPos + "\r\n")
elif (EventCheck == 1): #Ignition has been triggered
IgnPos = 'Active'
#JANUS_SER.sendUART("IgnPos : " + IgnPos + "\r\n")
elif (EventCheck == 2): #Both have been triggered
SwitchPos = 'Closed'
IgnPos = 'Active'
#JANUS_SER.sendUART("IgnPos : " + IgnPos + "\r\n")
#JANUS_SER.sendUART("SwitchPos : " + SwitchPos + "\r\n")
if (myApp.SMS_ENABLED == 'TRUE'):
res = JANUS_SMS.CheckNewSMS()
#If a new SMS is found and is valid, pass it to the command logic
if (res != '0'):
#We have received a new SMS, let's find what it wants us to do.
#JANUS_SER.sendUART("SMS Data : " + str(res) + "\r\n")
res = JANUS_SMS.SMSCommand(str(res))
# 0: Pass, action carried out and SMS sent back
# -1: Exception
# -2: Pass, Unrecognized change command or AT command received though
# -3: Unrecognized SMS
# -4: Error sending an SMS to the originating P/N
if (res == -1):
return
#If the STAT LED was updated via SMS, let's adjust it
res = JANUS_IO.Cellular_LED(myApp.SLED)
#AUTO ON Run time Change.
#Read current Auto-On status, 1 is active, 0 is inactive.
res = JANUS_IO.AutoONControl('READ', myApp.AUTOON)
#The below will be ignored if there is no change
#If Auto-on is OFF and we want it ON, set it.
if (res == 0 and myApp.AUTOON == 'ON'):
res = JANUS_IO.AutoONControl('SET', myApp.AUTOON)
if (res == -1):
return #Errored out
elif (res == -2):
JANUS_SER.sendUART("Timed out while waiting for MCU response. \r\n")
elif (res == 1):
JANUS_SER.sendUART("Auto ON Enabled. \r\n")
#If Auto-on is ON and we want it OFF, set it.
if (res == 1 and myApp.AUTOON == 'OFF'):
res = JANUS_IO.AutoONControl('SET', myApp.AUTOON)
if (res == -1):
return #Errored out
elif (res == -2):
JANUS_SER.sendUART("Timed out while waiting for MCU response. \r\n")
elif (res == 0):
JANUS_SER.sendUART("Auto ON Disabled. \r\n")
elif (res == '-1'):
#Exception
return
#If interval timer expires then send packet to server
if (timerB.isexpired() or FirstTimeThrough == 'TRUE'):
#The first time we drop into this loop we want to send data immediately, after that it's timer based sends.
FirstTimeThrough = 'FALSE' #Disable the flag
#######################
##BEGIN BUILDING STRING
#If we were woken up by one of the inputs, add it to the string to be sent
#This section can be used/altered to perhaps only display the wake up event for a certain amount of sends.
if (WakeupCause != ''):
WakeupString = WakeupCause
#JANUS_SER.sendUART("Wake up Event : " + WakeupCause + "\r\n")
#res = GPRS.send_CM("Wake up Event : " + WakeupCause + "\r\n",1,10)
#WakeupCause = '' #Clear the cause so it only gets reported the first time
else:
WakeupString = ''
#Build String to send to customer server, adjusts depending on what we want reported. Can only be one of these.
#CW Google Earth format
#STA = NMEA + ',' + IMEI + ',' + String1 + ',' + String2 + ',' + String3
#Strings 1/2/3 should remain in all sentences sent, but become null ('') when not being sent.
#The Strings follow a standard display format for the demo, so only send the actual information based on this format:
#String 1 will display in the Demo as "Switch"
#String 2 will display in the Demo as "Ignition"
#String 3 will display in the Demo as "Wake up Event"
if (myApp.NOSWITCH == 'TRUE' and myApp.IGNITION == 'TRUE'):
STA = GPSPositionTemp + ',' + ATC.properties.IMEI + ',' + SwitchPos + ',' + IgnPos + ',' + WakeupString
elif (myApp.NOSWITCH == 'TRUE' and myApp.IGNITION == 'FALSE'):
STA = GPSPositionTemp + ',' + ATC.properties.IMEI + ',' + SwitchPos + ',' + "" + ',' + WakeupString
elif (myApp.NOSWITCH == 'FALSE' and myApp.IGNITION == 'TRUE'):
STA = GPSPositionTemp + ',' + ATC.properties.IMEI + ',' + "" + ',' + IgnPos + ',' + WakeupString
elif (myApp.NOSWITCH == 'FALSE' and myApp.IGNITION == 'FALSE'):
STA = GPSPositionTemp + ',' + ATC.properties.IMEI + ',' + "" + ',' + "" + ',' + WakeupString
#Concatenate string, this allows store and forward during disconnects.
#STA is refreshed every time through, SENDSTRING is only cleared after a successful send
#Let's say 100B per string
#Max string length is 16kB, giving us (safely) 100 data points to store.
#This can be improved upon by utilizing a list, since each element in a list is capable of 16kB
#with a possible 4000 elements (keeping in mind overall memory limits)
if (StringCount < 100):
SENDSTRING.append(STA)
StringCount = StringCount+1
else:
JANUS_SER.sendUART("Store and forward limit reached (100). \r\n\r\n")
#######################
##END BUILDING STRING
###############################################################
##### Socket Open Check
#If socket closed, open it
DCD = MDM.getDCD()
#Check for a valid SS too
res = ATC.sendAtCmd('AT#SS',ATC.properties.CMD_TERMINATOR,0,20)
#If there is not a valid DCD OR the socket status shows that there is no socket open.
#We check for both because DCD seems to get stuck on 1 under certain conditions and we cannot set it, yet SS works fine.
if (DCD == 0 or res == "#SS: 1,0"):
JANUS_SER.sendUART("Opening socket to server: " + myApp.IP + ":" + myApp.PORT + "\r\n")
#Connect to customer's server
res = GPRS.openSocket(myApp.IP,myApp.PORT,1,myApp.USERNAME,myApp.PASSWORD,myApp.PROTOCOL,1)
if (res != 0):
JANUS_SER.sendUART("Connection failed to open. \r\n")
#Turn OFF the LED permanently until we have a valid connection
res = JANUS_IO.GPS_LED('OFF', myApp.ULED)
elif (res == 0):
JANUS_SER.sendUART("Socket opened successfully.\r\n")
#Turn ON the LED to show we have a valid connection
res = JANUS_IO.GPS_LED('ON', myApp.ULED)
JANUS_SER.sendUART("Polling GPS receiver for current location every " + myApp.INTERVAL + " second(s)\r\n")
#Do not return, end of this loop will handle the service checking
###############################################################
##### Socket Open Check
try:
#If socket open upload data
DCD = MDM.getDCD()
#Check for a valid SS too
res = ATC.sendAtCmd('AT#SS',ATC.properties.CMD_TERMINATOR,0,20)
#If there is a valid DCD AND the socket status shows that there is a valid socket connection too.
#We check for both because DCD seems to get stuck on 1 under certain conditions and we cannot set it, yet SS works fine.
if (DCD == 1 and res != "#SS: 1,0"):
#Update the GPS LED. This will turn the LED on/off during run time if it has been updated via SMS.
#Defaulted to ON
res = JANUS_IO.GPS_LED('ON', myApp.ULED)
#####Placeholder for built string OLD spot
#Strip the last entry of the pipe
#Pop the last item out, remove the last byte (the pipe) then append it back to the list.
#This covers single sends and block sends
## LastItem = SENDSTRING.pop(StringCount-1)
## ItemLength = len(LastItem)
## LastItem = LastItem[0:ItemLength-1]
## SENDSTRING.append(LastItem)
JANUS_SER.sendUART("Sending data: \r\n")
res = 0
x = 0
while (res == 0 and x < StringCount):
#Send Data
JANUS_SER.sendUART(str(SENDSTRING[x]) + "\r\n")
res = GPRS.send_CM(SENDSTRING[x],1,10)
x = x+1
if (res == 1):
JANUS_SER.sendUART("\r\n\r\nData Empty, Error receiving info from GPS module\r\n")
return
if (res == -2):
JANUS_SER.sendUART("\r\n\r\nTimed out while sending data, checking socket connection\r\n") #Do not return, drop to service checks
#Add the pipe to the end again since this got disconnected mid-send procedure and will become a store and forward send.
## LastItem = SENDSTRING.pop(StringCount-1)
## LastItem = LastItem + '|'
## SENDSTRING.append(LastItem)
else:
JANUS_SER.sendUART("\r\n\r\nData Sent Successfully.\r\n\r\n")
#Blink OFF the LED to indicate data was sent
res = JANUS_IO.GPS_LED('OFF', myApp.ULED)
res = JANUS_IO.GPS_LED('ON', myApp.ULED)
if (IgnPos == 'Inactive' and myApp.AUTOON == 'OFF' and myApp.IGNITIONFOLLOW == 'TRUE'):
#Special Case, auto-on is not active and we want to only be active while the ignition is active.
#Inigition has dropped, we've sent the last data packet, now shut the unit down
res = ATC.sendAtCmd('AT#SHDN',ATC.properties.CMD_TERMINATOR,0,20)
#Put the Switch and Ignition I/O back to default, clear the list and counter
SwitchPos = 'Open'
IgnPos = 'Inactive'
SENDSTRING = []
StringCount = 0
#Exit data mode
#DEBUG.sendMsg('Exiting data mode\r\n')
#res = ATC.exitSocketDataMode()
#Close Socket
#Pass in: sockNum
#res = ATC.closeSocket('1')
#DEBUG.sendMsg('Connection closed\r\n')
break
else:
JANUS_SER.sendUART("\r\nConnection not available, checking status.\r\n")
#Wait until module is registered to GSM Network
#res = NETWORK.isGsmRegistered(180) #Wait 180 seconds for module to obtain GSM registration
#if (res == -1):
# ATC.reboot()
#Wait until module is attached to GPRS
#res = NETWORK.isGprsAttached(180) #Wait 180 seconds for module to obtain GPRS Attachment
#if (res == -1):
# ATC.reboot()
#What is the signal strength?
res = ATC.sendAtCmd('AT+CSQ',ATC.properties.CMD_TERMINATOR,0,5)
JANUS_SER.sendUART("Signal Strength (AT+CSQ): " + res + "\r\n")
#Still registered?
res = ATC.sendAtCmd('AT+CREG?',ATC.properties.CMD_TERMINATOR,0,5)
JANUS_SER.sendUART("Registration Check (AT+CREG?): " + res + "\r\n")
#GPRS Available?
res = ATC.sendAtCmd('AT+CGREG?',ATC.properties.CMD_TERMINATOR,0,5)
JANUS_SER.sendUART("GPRS Availability (AT+CGREG?): " + res + "\r\n")
#Is a PDP context activated?
res = ATC.sendAtCmd('AT#SGACT?',ATC.properties.CMD_TERMINATOR,0,20)
JANUS_SER.sendUART("PDP Context status (AT#SGACT?): " + res + "\r\n\r\n")
break
except:
JANUS_SER.sendUART("Script encountered an exception while uploading data to server\r\n")
JANUS_SER.sendUART("Exception Type: " + str(sys.exc_type) + "\r\n")
JANUS_SER.sendUART("MODULE -> LobosTrack\r\n")
break
## Re-Start timeout timer
timerB = timers.timer(0)
timerB.start(int(myApp.INTERVAL))
#DEBUG.CLS() #Clear screen command for VT100 terminals
except:
print "Script encountered an exception"
print "Exception Type: " + str(sys.exc_type)
print "MODULE -> TerminusS2E"
return
def main():
try:
timerA = timers.timer(0)
timerA.start(1)
# Set Global Watchdog timeout in Seconds
MOD.watchdogEnable(300)
#Increase CPU speed at cost of increased current consumption
ATC.sendAtCmd('AT#CPUMODE=1',ATC.properties.CMD_TERMINATOR,0,5)
#Turn off GSM TX/RX
ATC.sendAtCmd('AT+CFUN=4',ATC.properties.CMD_TERMINATOR,0,5)
#Initialize MS20 Receiver
res = MS20.initGPS('9600','8N1')
if not(res == 0):
if (res == -1):
DEBUG_CF.sendMsg("MS20 Exception occurred\r\n",myApp.RUN_MODE)
elif (res == -3):
DEBUG_CF.sendMsg("NMEA Command response Checksum fail\r\n",myApp.RUN_MODE)
elif (res == -4):
DEBUG_CF.sendMsg("No NMEA Command response\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("Is NAVSYNC serial port connected to TRACE port via NULL MODEM cable?\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("For CF_EVAL_PCB001 V3.1 evaluation boards or newer => SW1, MODE1 = ON\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("See GSM865CF Plug-in Terminal GPS Demonstration User Guide for more info\r\n",myApp.RUN_MODE)
elif (res == -5):
DEBUG_CF.sendMsg("Incorrect NMEA command response\r\n",myApp.RUN_MODE)
elif (res > 0):
DEBUG_CF.sendMsg("MS20 Error Number: " + str(res) + "\r\n",myApp.RUN_MODE)
else:
DEBUG_CF.sendMsg("Unknown error\r\n",myApp.RUN_MODE)
MOD.sleep(40)
return
DEBUG_CF.sendMsg("MS20 Initialization Complete\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("GPS Application Version: " + MS20.GPSdata.APP_VER + "\r\n",myApp.RUN_MODE)
# Wait for GPS module to obtain position data
DEBUG_CF.sendMsg("Waiting for valid position",myApp.RUN_MODE)
#Poll NMEA GPGLL Sentence
if (MS20.pollNMEA('2',5) == 0): exitLoop = MS20.GPSdata.GPGLL.split(',')[6]
while(exitLoop != 'A'):
MOD.watchdogReset()
#Poll NMEA GPGLL Sentence
if (MS20.pollNMEA('2',5) == 0): exitLoop = MS20.GPSdata.GPGLL.split(',')[6]
DEBUG_CF.sendMsg(".",myApp.RUN_MODE)
DEBUG_CF.sendMsg("\r\nPosition acquired: " +str(timerA.count()) + " Seconds (Referenced to script start time)\r\n",myApp.RUN_MODE)
#Increase CPU speed during TX/RX only
ATC.sendAtCmd('AT#CPUMODE=2',ATC.properties.CMD_TERMINATOR,0,5)
#Activate Low Power mode, Turn off GSM TX/RX
ATC.sendAtCmd('AT+CFUN=5',ATC.properties.CMD_TERMINATOR,0,5)
#Set Network specific settings
res = NETWORK.initGsmNetwork(myApp.NETWORK,myApp.BAND)
if (res == -1):
return
DEBUG_CF.sendMsg("Network Initialization Complete\r\n",myApp.RUN_MODE)
#Wait for GSM Registration
DEBUG_CF.sendMsg("Waiting for GSM Registration",myApp.RUN_MODE)
#Check GSM registration
exitLoop = NETWORK.isGsmRegistered(1)
while(exitLoop != 0):
MOD.watchdogReset()
#Check GSM registration
exitLoop = NETWORK.isGsmRegistered(1)
DEBUG_CF.sendMsg(".",myApp.RUN_MODE)
DEBUG_CF.sendMsg("\r\nTerminal is registered to a GSM network\r\n",myApp.RUN_MODE)
#Init GPRS
GPRS.init('1',myApp.APN)
DEBUG_CF.sendMsg("GPRS Initialization Complete\r\n",myApp.RUN_MODE)
#Wait for GPRS attach
DEBUG_CF.sendMsg("Waiting for GPRS Attach",myApp.RUN_MODE)
#Check GPRS Attach
exitLoop = NETWORK.isGprsAttached(1)
while(exitLoop != 0):
MOD.watchdogReset()
#Check GPRS Attach
exitLoop = NETWORK.isGprsAttached(1)
DEBUG_CF.sendMsg(".",myApp.RUN_MODE)
DEBUG_CF.sendMsg("\r\nTerminal is attached to GPRS service\r\n",myApp.RUN_MODE)
#Record IMEI number
myApp.IMEI = ATC.sendAtCmd('AT+CGSN',ATC.properties.CMD_TERMINATOR,0,5)
DEBUG_CF.sendMsg("IMEI #: " + myApp.IMEI + "\r\n",myApp.RUN_MODE)
# Start timeout timer
timerB = timers.timer(0)
timerB.start(1)
while(not(timerB.isexpired())): exitCode = -1
# Loop forever, without this loop the script would run once and exit script mode. On reboot or power-on the script would run once more
while (1):
exitCode = -1
while (exitCode==-1):
MOD.watchdogReset()
#If interval timer expires then send packet to server
if (timerB.isexpired()):
#Poll NMEA GPGLL Sentence
res = MS20.pollNMEA('2',5)
DEBUG_CF.sendMsg("Current GPGLL sentence: " + MS20.GPSdata.GPGLL,myApp.RUN_MODE)
DEBUG_CF.sendMsg("Opening Connection to server: " + myApp.IP + ":" + myApp.PORT + "\r\n",myApp.RUN_MODE)
#Connect to server
#Pass in: IP Address, IP Port, sockNum, GPRSuserName, GPRSuserPassword,Command Mode
res = GPRS.openSocket(myApp.IP,myApp.PORT,'1','','',myApp.PROTOCOL,'1')
try:
#If socket open upload data
if (res == 'OK'):
DEBUG_CF.sendMsg("Connection opened\r\n",myApp.RUN_MODE)
#Build String to send to customer server
STR1 = myApp.IMEI +',' + MS20.GPSdata.GPGLL
DEBUG_CF.sendMsg("Sending Data: " + STR1,myApp.RUN_MODE)
#Send STR1 to server
res = GPRS.send_CM(STR1,1,10)
DEBUG_CF.sendMsg("Data Sent\r\n",myApp.RUN_MODE)
#Close Socket
res = GPRS.closeSocket('1')
DEBUG_CF.sendMsg("Connection Closed\r\n",myApp.RUN_MODE)
exitCode = 0
else:
DEBUG_CF.sendMsg("Connection failed to open\r\n",myApp.RUN_MODE)
#What is the signal strength?
res = ATC.sendAtCmd('AT+CSQ',ATC.properties.CMD_TERMINATOR,0,5)
DEBUG_CF.sendMsg("Signal Strength (AT+CSQ): " + res + "\r\n",myApp.RUN_MODE)
# Is Terminus still connected to GSM Network?
res = NETWORK.isGsmRegistered(1)
if (res == 0):
DEBUG_CF.sendMsg("GSM865CF is registered on GSM network\r\n",myApp.RUN_MODE)
else:
DEBUG_CF.sendMsg("GSM865CF is NOT registered on GSM network\r\n",myApp.RUN_MODE)
#Is a PDP context activated?
res = ATC.sendAtCmd('AT#SGACT?',ATC.properties.CMD_TERMINATOR,0,20)
DEBUG_CF.sendMsg("PDP Context status (AT#SGACT?): " + res + "\r\n",myApp.RUN_MODE)
# Is Terminus still attached to GPRS service?
res = NETWORK.isGprsAttached(1)
if (res == 0):
DEBUG_CF.sendMsg("GSM865CF is attached to GPRS service\r\n",myApp.RUN_MODE)
else:
DEBUG_CF.sendMsg("GSM865CF is NOT attached to GPRS service\r\n",myApp.RUN_MODE)
except:
DEBUG_CF.sendMsg("Script encountered an exception while uploading data to server\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("Exception Type: " + str(sys.exc_type) + "\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("MODULE -> GSM865CF_GPS\r\n",myApp.RUN_MODE)
return
else:
DEBUG_CF.CLS(myApp.RUN_MODE)
DEBUG_CF.sendMsg("Next update in: " + str(int(myApp.INTERVAL) - timerB.count()) + " Seconds\r\n",myApp.RUN_MODE)
MOD.sleep(10)
## Re-Start timeout timer
timerB = timers.timer(0)
timerB.start(int(myApp.INTERVAL))
except:
DEBUG_CF.sendMsg("Script encountered an exception\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("Exception Type: " + str(sys.exc_type) + "\r\n",myApp.RUN_MODE)
DEBUG_CF.sendMsg("MODULE -> GSM865CF_GPS\r\n",myApp.RUN_MODE)
return
