def init_values(values):
"""Initialize values that are used throughout the postprocessor."""
#
global UNITS
PostUtilsArguments.init_shared_values(values)
#
# Set any values here that need to override the default values set
# in the init_shared_values routine.
#
values["ENABLE_COOLANT"] = True
#
# Used in the argparser code as the "name" of the postprocessor program.
# This would normally show up in the usage message in the TOOLTIP_ARGS,
# but we are suppressing the usage message, so it doesn't show up after all.
#
values["MACHINE_NAME"] = "mach3_4"
# Enable special processing for operations with "Adaptive" in the name
values["OUTPUT_ADAPTIVE"] = True
# Output the machine name for mach3_mach4 instead of the machine units alone.
values["OUTPUT_MACHINE_NAME"] = True
# the order of parameters
# mach3_mach4 doesn't want K properties on XY plane; Arcs need work.
values["PARAMETER_ORDER"] = [
"X",
"Y",
"Z",
"A",
"B",
"C",
"I",
"J",
"F",
"S",
"T",
"Q",
"R",
"L",
"H",
"D",
"P",
]
#
# Any commands in this value will be output as the last commands
# in the G-code file.
#
values["POSTAMBLE"] = """M05
G17 G54 G90 G80 G40
M2"""
values["POSTPROCESSOR_FILE_NAME"] = __name__
#
# Any commands in this value will be output after the header and
# safety block at the beginning of the G-code file.
#
values["PREAMBLE"] = """G17 G54 G40 G49 G80 G90"""
# Output the machine name for mach3_mach4 instead of the machine units alone.
values["SHOW_MACHINE_UNITS"] = False
values["UNITS"] = UNITS
def init_values(values):
"""Initialize values that are used throughout the postprocessor."""
#
global UNITS
PostUtilsArguments.init_shared_values(values)
#
# Set any values here that need to override the default values set
# in the init_shared_values routine.
#
#
# If this is set to True, then commands that are placed in
# comments that look like (MC_RUN_COMMAND: blah) will be output.
#
values["ENABLE_MACHINE_SPECIFIC_COMMANDS"] = True
#
# Used in the argparser code as the "name" of the postprocessor program.
# This would normally show up in the usage message in the TOOLTIP_ARGS,
# but we are suppressing the usage message, so it doesn't show up after all.
#
values["MACHINE_NAME"] = "Grbl"
#
# Default to outputting Path labels at the beginning of each Path.
#
values["OUTPUT_PATH_LABELS"] = True
#
# Default to not outputting M6 tool changes (comment it) as grbl currently does not handle it
#
values["OUTPUT_TOOL_CHANGE"] = False
#
# The order of the parameters.
# Arcs may only work on the XY plane (this needs to be verified).
#
values["PARAMETER_ORDER"] = [
"X",
"Y",
"Z",
"A",
"B",
"C",
"U",
"V",
"W",
"I",
"J",
"K",
"F",
"S",
"T",
"Q",
"R",
"L",
"P",
]
#
# Any commands in this value will be output as the last commands
# in the G-code file.
#
values["POSTAMBLE"] = """M5
G17 G90
M2"""
values["POSTPROCESSOR_FILE_NAME"] = __name__
#
# Any commands in this value will be output after the header and
# safety block at the beginning of the G-code file.
#
values["PREAMBLE"] = """G17 G90"""
#
# Do not show the current machine units just before the PRE_OPERATION.
#
values["SHOW_MACHINE_UNITS"] = False
values["UNITS"] = UNITS
#
# Default to not outputting a G43 following tool changes
#
values["USE_TLO"] = False
def init_values(values):
"""Initialize values that are used throughout the postprocessor."""
#
global UNITS
PostUtilsArguments.init_shared_values(values)
#
# Set any values here that need to override the default values set
# in the init_shared_values routine.
#
# Use 4 digits for axis precision by default.
#
values["AXIS_PRECISION"] = 4
values["DEFAULT_AXIS_PRECISION"] = 4
values["DEFAULT_INCH_AXIS_PRECISION"] = 4
#
# Use ";" as the comment symbol
#
values["COMMENT_SYMBOL"] = ";"
#
# Use 1 digit for feed precision by default.
#
values["FEED_PRECISION"] = 1
values["DEFAULT_FEED_PRECISION"] = 1
values["DEFAULT_INCH_FEED_PRECISION"] = 1
#
# This value usually shows up in the post_op comment as "Finish operation:".
# Change it to "End" to produce "End operation:".
#
values["FINISH_LABEL"] = "End"
#
# If this value is True, then a list of tool numbers
# with their labels are output just before the preamble.
#
values["LIST_TOOLS_IN_PREAMBLE"] = True
#
# Used in the argparser code as the "name" of the postprocessor program.
# This would normally show up in the usage message in the TOOLTIP_ARGS,
# but we are suppressing the usage message, so it doesn't show up after all.
#
values["MACHINE_NAME"] = "Centroid"
#
# This list controls the order of parameters in a line during output.
# centroid doesn't want K properties on XY plane; Arcs need work.
#
values["PARAMETER_ORDER"] = [
"X",
"Y",
"Z",
"A",
"B",
"I",
"J",
"F",
"S",
"T",
"Q",
"R",
"L",
"H",
]
#
# Any commands in this value will be output as the last commands
# in the G-code file.
#
values["POSTAMBLE"] = """M99"""
values["POSTPROCESSOR_FILE_NAME"] = __name__
#
# Any commands in this value will be output after the header and
# safety block at the beginning of the G-code file.
#
values["PREAMBLE"] = """G53 G00 G17"""
#
# Output any messages.
#
values["REMOVE_MESSAGES"] = False
#
# Any commands in this value are output after the header but before the preamble,
# then again after the TOOLRETURN but before the POSTAMBLE.
#
values["SAFETYBLOCK"] = """G90 G80 G40 G49"""
#
# Do not show the current machine units just before the PRE_OPERATION.
#
values["SHOW_MACHINE_UNITS"] = False
#
# Do not show the current operation label just before the PRE_OPERATION.
#
values["SHOW_OPERATION_LABELS"] = False
#
# Do not output an M5 command to stop the spindle for tool changes.
#
values["STOP_SPINDLE_FOR_TOOL_CHANGE"] = False
#
# spindle off, height offset canceled, spindle retracted
# (M25 is a centroid command to retract spindle)
#
values["TOOLRETURN"] = """M5
M25
G49 H0"""
values["UNITS"] = UNITS
#
# Default to not outputting a G43 following tool changes
#
values["USE_TLO"] = False
def init_values(values):
"""Initialize values that are used throughout the postprocessor."""
#
global UNITS
PostUtilsArguments.init_shared_values(values)
#
# Set any values here that need to override the default values set
# in the init_shared_values routine.
#
# Turn off as much functionality as possible by default.
# Then the tests can turn back on the appropriate options as needed.
#
# Used in the argparser code as the "name" of the postprocessor program.
# This would normally show up in the usage message in the TOOLTIP_ARGS,
# but we are suppressing the usage message, so it doesn't show up after all.
#
values["MACHINE_NAME"] = "test"
#
# Don't output comments by default
#
values["OUTPUT_COMMENTS"] = False
#
# Don't output the header by default
#
values["OUTPUT_HEADER"] = False
#
# Convert M56 tool change commands to comments,
# which are then suppressed by default.
#
values["OUTPUT_TOOL_CHANGE"] = False
#
# Enable as many parameters as possible to be output by default
#
values["PARAMETER_ORDER"] = [
"X",
"Y",
"Z",
"A",
"B",
"C",
"U",
"V",
"W",
"I",
"J",
"K",
"F",
"S",
"T",
"Q",
"R",
"L",
"H",
"D",
"P",
]
values["POSTPROCESSOR_FILE_NAME"] = __name__
#
# Do not show the editor by default since we are testing.
#
values["SHOW_EDITOR"] = False
#
# Don't show the current machine units by default
#
values["SHOW_MACHINE_UNITS"] = False
#
# Don't show the current operation label by default.
#
values["SHOW_OPERATION_LABELS"] = False
#
# Don't output an M5 command to stop the spindle after an M6 tool change by default.
#
values["STOP_SPINDLE_FOR_TOOL_CHANGE"] = False
#
# Don't output a G43 tool length command following tool changes by default.
#
values["USE_TLO"] = False
values["UNITS"] = UNITS