def __init__(self, miso=5, mosi=18, clk=19, cs=13, dc=12, rst=4, backlight=2, spihost=esp.enum.HSPI_HOST, mhz=40, factor=4, hybrid=True):
# Make sure Micropython was built such that color won't require processing before DMA
if lv.color_t.SIZE != 2:
raise RuntimeError('ili9341 micropython driver requires defining LV_COLOR_DEPTH=16')
if not hasattr(lv.color_t().ch, 'green_l'):
raise RuntimeError('ili9341 micropython driver requires defining LV_COLOR_16_SWAP=1')
# Initializations
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.rst = rst
self.backlight = backlight
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.buf_size = (self.width * self.height * lv.color_t.SIZE) // factor
self.init()
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.CAP.DMA)
self.buf2 = esp.heap_caps_malloc(self.buf_size, esp.CAP.DMA)
if self.buf1 and self.buf2:
print("Double buffer")
elif self.buf1:
print("Single buffer")
else:
raise RuntimeError("Not enough DMA-able memory to allocate display buffer")
lv.disp_buf_init(self.disp_buf, self.buf1, self.buf2, self.buf_size // lv.color_t.SIZE)
lv.disp_drv_init(self.disp_drv)
self.disp_drv.user_data = {'dc': self.dc, 'spi': self.spi}
self.disp_drv.buffer = self.disp_buf
self.disp_drv.flush_cb = esp.ili9341_flush if self.hybrid and hasattr(esp, 'ili9341_flush') else self.flush
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
lv.disp_drv_register(self.disp_drv)
def __init__(self,
miso=-1,
mosi=-1,
clk=-1,
cs=25,
spihost=esp.HSPI_HOST,
mhz=5,
transpose=False,
touch_margin=100):
# Initializations
self.screen_width = lv.disp_get_hor_res(lv.disp_t.cast(None))
self.screen_height = lv.disp_get_ver_res(lv.disp_t.cast(None))
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.spihost = spihost
self.mhz = mhz
self.cal_x0 = None
self.transpose = transpose
self.touch_margin = touch_margin
self.touch_count = 0
self.touch_cycles = 0
self.spi_init()
# Prepare buffer with commands to send to device
nc = len(self.CMDS)
self.buflen = 2 * nc * REP + 1 # +1 for final CMD_OFF
self.txbuf = esp.heap_caps_malloc(self.buflen, esp.MALLOC_CAP.DMA)
txbuf = self.txbuf.__dereference__(self.buflen)
for c in range(nc):
for r in range(REP):
txbuf[(c * REP + r) * 2 +
0] = self.CMDS[c] # first byte is command, second is 0
txbuf[(c * REP + r) * 2 + 1] = 0
txbuf[2 * nc * REP] = CMD_OFF
# print("xpt2046 txbuf:", ["%02x" % v for v in txbuf])
self.rxbuf = esp.heap_caps_malloc(self.buflen, esp.MALLOC_CAP.DMA)
indev_drv = lv.indev_drv_t()
lv.indev_drv_init(indev_drv)
indev_drv.type = lv.INDEV_TYPE.POINTER
indev_drv.read_cb = self.read
lv.indev_drv_register(indev_drv)
print("xpt2046 touch initialized")
def __init__(self,
miso=5,
mosi=18,
clk=19,
cs=13,
dc=12,
rst=4,
power=14,
backlight=15,
backlight_on=0,
power_on=0,
spihost=esp.HSPI_HOST,
mhz=40,
factor=4,
hybrid=True,
width=240,
height=320,
colormode=COLOR_MODE_BGR,
rot=PORTRAIT,
invert=False,
double_buffer=True):
# Make sure Micropython was built such that color won't require processing before DMA
if lv.color_t.SIZE != 2:
raise RuntimeError(
'ili9341 micropython driver requires defining LV_COLOR_DEPTH=16'
)
if colormode == COLOR_MODE_BGR and not hasattr(lv.color_t().ch,
'green_l'):
raise RuntimeError(
'ili9341 BGR color mode requires defining LV_COLOR_16_SWAP=1')
# Initializations
self.width = width
self.height = height
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.rst = rst
self.power = power
self.backlight = backlight
self.backlight_on = backlight_on
self.power_on = power_on
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.buf_size = (self.width * self.height * lv.color_t.SIZE) // factor
self.init_cmds = [
{
'cmd': 0xCF,
'data': bytes([0x00, 0x83, 0X30])
},
{
'cmd': 0xED,
'data': bytes([0x64, 0x03, 0X12, 0X81])
},
{
'cmd': 0xE8,
'data': bytes([0x85, 0x01, 0x79])
},
{
'cmd': 0xCB,
'data': bytes([0x39, 0x2C, 0x00, 0x34, 0x02])
},
{
'cmd': 0xF7,
'data': bytes([0x20])
},
{
'cmd': 0xEA,
'data': bytes([0x00, 0x00])
},
{
'cmd': 0xC0,
'data': bytes([0x26])
}, # Power control
{
'cmd': 0xC1,
'data': bytes([0x11])
}, # Power control
{
'cmd': 0xC5,
'data': bytes([0x35, 0x3E])
}, # VCOM control
{
'cmd': 0xC7,
'data': bytes([0xBE])
}, # VCOM control
{
'cmd': 0x36,
'data': bytes([rot | colormode])
}, # Memory Access Control
{
'cmd': 0x3A,
'data': bytes([0x55])
}, # Pixel Format Set
{
'cmd': 0xB1,
'data': bytes([0x00, 0x1B])
},
{
'cmd': 0xF2,
'data': bytes([0x08])
},
{
'cmd': 0x26,
'data': bytes([0x01])
},
{
'cmd':
0xE0,
'data':
bytes([
0x1F, 0x1A, 0x18, 0x0A, 0x0F, 0x06, 0x45, 0X87, 0x32, 0x0A,
0x07, 0x02, 0x07, 0x05, 0x00
])
},
{
'cmd':
0XE1,
'data':
bytes([
0x00, 0x25, 0x27, 0x05, 0x10, 0x09, 0x3A, 0x78, 0x4D, 0x05,
0x18, 0x0D, 0x38, 0x3A, 0x1F
])
},
{
'cmd': 0x2A,
'data': bytes([0x00, 0x00, 0x00, 0xEF])
},
{
'cmd': 0x2B,
'data': bytes([0x00, 0x00, 0x01, 0x3f])
},
{
'cmd': 0x2C,
'data': bytes([0])
},
{
'cmd': 0xB7,
'data': bytes([0x07])
},
{
'cmd': 0xB6,
'data': bytes([0x0A, 0x82, 0x27, 0x00])
},
{
'cmd': 0x11,
'data': bytes([0]),
'delay': 100
},
{
'cmd': 0x29,
'data': bytes([0]),
'delay': 100
}
]
if invert:
self.init_cmds.append({'cmd': 0x21})
self.init()
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.MALLOC_CAP.DMA)
self.buf2 = esp.heap_caps_malloc(
self.buf_size, esp.MALLOC_CAP.DMA) if double_buffer else None
if self.buf1 and self.buf2:
print("Double buffer")
elif self.buf1:
print("Single buffer")
else:
raise RuntimeError(
"Not enough DMA-able memory to allocate display buffer")
self.disp_buf = lv.disp_buf_t()
self.disp_drv = lv.disp_drv_t()
lv.disp_buf_init(self.disp_buf, self.buf1, self.buf2,
self.buf_size // lv.color_t.SIZE)
lv.disp_drv_init(self.disp_drv)
self.disp_drv.user_data = {'dc': self.dc, 'spi': self.spi}
self.disp_drv.buffer = self.disp_buf
self.disp_drv.flush_cb = esp.ili9341_flush if self.hybrid and hasattr(
esp, 'ili9341_flush') else self.flush
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
lv.disp_drv_register(self.disp_drv)
def disp_spi_init(self):
# Register finalizer callback to deinit SPI.
# This would get called on soft reset.
self.finalizer = lvesp32.cb_finalizer(self.deinit)
lvesp32.init()
buscfg = esp.spi_bus_config_t({
"miso_io_num": self.miso,
"mosi_io_num": self.mosi,
"sclk_io_num": self.clk,
"quadwp_io_num": -1,
"quadhd_io_num": -1,
"max_transfer_sz": self.buf_size,
})
devcfg = esp.spi_device_interface_config_t({
"clock_speed_hz":
self.mhz * 1000 * 1000, # Clock out at DISP_SPI_MHZ MHz
"mode":
0, # SPI mode 0
"spics_io_num":
self.cs, # CS pin
"queue_size":
2,
#"flags": esp.SPI_DEVICE.HALFDUPLEX,
"duty_cycle_pos":
128,
})
if self.hybrid and hasattr(esp, 'ili9341_post_cb_isr'):
devcfg.pre_cb = None
devcfg.post_cb = esp.ili9341_post_cb_isr
else:
devcfg.pre_cb = esp.spi_pre_cb_isr
devcfg.post_cb = esp.spi_post_cb_isr
esp.gpio_pad_select_gpio(self.cs)
# Initialize the SPI bus, if needed.
if buscfg.miso_io_num >= 0 and \
buscfg.mosi_io_num >= 0 and \
buscfg.sclk_io_num >= 0:
esp.gpio_pad_select_gpio(self.miso)
esp.gpio_pad_select_gpio(self.mosi)
esp.gpio_pad_select_gpio(self.clk)
esp.gpio_set_direction(self.miso, esp.GPIO_MODE.INPUT)
esp.gpio_set_pull_mode(self.miso, esp.GPIO.PULLUP_ONLY)
esp.gpio_set_direction(self.mosi, esp.GPIO_MODE.OUTPUT)
esp.gpio_set_direction(self.clk, esp.GPIO_MODE.OUTPUT)
ret = esp.spi_bus_initialize(self.spihost, buscfg, 1)
if ret != 0: raise RuntimeError("Failed initializing SPI bus")
self.trans_buffer = esp.heap_caps_malloc(TRANS_BUFFER_LEN,
esp.MALLOC_CAP.DMA)
self.cmd_trans_data = self.trans_buffer.__dereference__(1)
self.word_trans_data = self.trans_buffer.__dereference__(4)
# Attach the LCD to the SPI bus
ptr_to_spi = esp.C_Pointer()
ret = esp.spi_bus_add_device(self.spihost, devcfg, ptr_to_spi)
if ret != 0: raise RuntimeError("Failed adding SPI device")
self.spi = ptr_to_spi.ptr_val
self.bytes_transmitted = 0
completed_spi_transaction = esp.spi_transaction_t()
cast_spi_transaction_instance = esp.spi_transaction_t.cast_instance
def post_isr(arg):
reported_transmitted = self.bytes_transmitted
if reported_transmitted > 0:
print('- Completed DMA of %d bytes (mem_free=0x%X)' %
(reported_transmitted, gc.mem_free()))
self.bytes_transmitted -= reported_transmitted
# Called in ISR context!
def flush_isr(spi_transaction_ptr):
lv.disp_flush_ready(self.disp_drv)
# esp.spi_device_release_bus(self.spi)
esp.get_ccount(self.end_time_ptr)
# cast_spi_transaction_instance(completed_spi_transaction, spi_transaction_ptr)
# self.bytes_transmitted += completed_spi_transaction.length
# try:
# micropython.schedule(post_isr, None)
# except RuntimeError:
# pass
self.spi_callbacks = esp.spi_transaction_set_cb(None, flush_isr)
class ili9341:
width = const(240)
height = const(320)
######################################################
disp_buf = lv.disp_buf_t()
disp_drv = lv.disp_drv_t()
# "power" and "backlight" are reversed logic! 0 means ON.
def __init__(self,
miso=5,
mosi=18,
clk=19,
cs=13,
dc=12,
rst=4,
power=14,
backlight=15,
spihost=esp.enum.HSPI_HOST,
mhz=40,
factor=4,
hybrid=True):
# Make sure Micropython was built such that color won't require processing before DMA
if lv.color_t.SIZE != 2:
raise RuntimeError(
'ili9341 micropython driver requires defining LV_COLOR_DEPTH=16'
)
if not hasattr(lv.color_t().ch, 'green_l'):
raise RuntimeError(
'ili9341 micropython driver requires defining LV_COLOR_16_SWAP=1'
)
# Initializations
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.rst = rst
self.power = power
self.backlight = backlight
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.buf_size = (self.width * self.height * lv.color_t.SIZE) // factor
self.init()
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.CAP.DMA)
self.buf2 = esp.heap_caps_malloc(self.buf_size, esp.CAP.DMA)
if self.buf1 and self.buf2:
print("Double buffer")
elif self.buf1:
print("Single buffer")
else:
raise RuntimeError(
"Not enough DMA-able memory to allocate display buffer")
lv.disp_buf_init(self.disp_buf, self.buf1, self.buf2,
self.buf_size // lv.color_t.SIZE)
lv.disp_drv_init(self.disp_drv)
self.disp_drv.user_data = {'dc': self.dc, 'spi': self.spi}
self.disp_drv.buffer = self.disp_buf
self.disp_drv.flush_cb = esp.ili9341_flush if self.hybrid and hasattr(
esp, 'ili9341_flush') else self.flush
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
lv.disp_drv_register(self.disp_drv)
######################################################
init_cmds = [
{
'cmd': 0xCF,
'data': bytes([0x00, 0x83, 0X30])
},
{
'cmd': 0xED,
'data': bytes([0x64, 0x03, 0X12, 0X81])
},
{
'cmd': 0xE8,
'data': bytes([0x85, 0x01, 0x79])
},
{
'cmd': 0xCB,
'data': bytes([0x39, 0x2C, 0x00, 0x34, 0x02])
},
{
'cmd': 0xF7,
'data': bytes([0x20])
},
{
'cmd': 0xEA,
'data': bytes([0x00, 0x00])
},
{
'cmd': 0xC0,
'data': bytes([0x26])
}, # Power control
{
'cmd': 0xC1,
'data': bytes([0x11])
}, # Power control
{
'cmd': 0xC5,
'data': bytes([0x35, 0x3E])
}, # VCOM control
{
'cmd': 0xC7,
'data': bytes([0xBE])
}, # VCOM control
{
'cmd': 0x36,
'data': bytes([0x48])
}, # Memory Access Control
{
'cmd': 0x3A,
'data': bytes([0x55])
}, # Pixel Format Set
{
'cmd': 0xB1,
'data': bytes([0x00, 0x1B])
},
{
'cmd': 0xF2,
'data': bytes([0x08])
},
{
'cmd': 0x26,
'data': bytes([0x01])
},
{
'cmd':
0xE0,
'data':
bytes([
0x1F, 0x1A, 0x18, 0x0A, 0x0F, 0x06, 0x45, 0X87, 0x32, 0x0A,
0x07, 0x02, 0x07, 0x05, 0x00
])
},
{
'cmd':
0XE1,
'data':
bytes([
0x00, 0x25, 0x27, 0x05, 0x10, 0x09, 0x3A, 0x78, 0x4D, 0x05,
0x18, 0x0D, 0x38, 0x3A, 0x1F
])
},
{
'cmd': 0x2A,
'data': bytes([0x00, 0x00, 0x00, 0xEF])
},
{
'cmd': 0x2B,
'data': bytes([0x00, 0x00, 0x01, 0x3f])
},
{
'cmd': 0x2C,
'data': bytes([0])
},
{
'cmd': 0xB7,
'data': bytes([0x07])
},
{
'cmd': 0xB6,
'data': bytes([0x0A, 0x82, 0x27, 0x00])
},
{
'cmd': 0x11,
'data': bytes([0]),
'delay': 100
},
{
'cmd': 0x29,
'data': bytes([0]),
'delay': 100
}
]
######################################################
def disp_spi_init(self):
buscfg = esp.spi_bus_config_t({
"miso_io_num": self.miso,
"mosi_io_num": self.mosi,
"sclk_io_num": self.clk,
"quadwp_io_num": -1,
"quadhd_io_num": -1,
"max_transfer_sz": self.buf_size,
})
devcfg = esp.spi_device_interface_config_t({
"clock_speed_hz":
self.mhz * 1000 * 1000, # Clock out at DISP_SPI_MHZ MHz
"mode":
0, # SPI mode 0
"spics_io_num":
self.cs, # CS pin
"queue_size":
2,
"flags":
esp.ESP.HALF_DUPLEX,
"duty_cycle_pos":
128,
})
if self.hybrid and hasattr(esp, 'ili9341_post_cb_isr'):
devcfg.pre_cb = None
devcfg.post_cb = esp.ili9341_post_cb_isr
else:
devcfg.pre_cb = esp.spi_pre_cb_isr
devcfg.post_cb = esp.spi_post_cb_isr
esp.gpio_pad_select_gpio(self.miso)
esp.gpio_pad_select_gpio(self.mosi)
esp.gpio_pad_select_gpio(self.clk)
esp.gpio_set_direction(self.miso, esp.GPIO_MODE.INPUT)
esp.gpio_set_pull_mode(self.miso, esp.GPIO.PULLUP_ONLY)
esp.gpio_set_direction(self.mosi, esp.GPIO_MODE.OUTPUT)
esp.gpio_set_direction(self.clk, esp.GPIO_MODE.OUTPUT)
esp.gpio_pad_select_gpio(self.cs)
# Initialize the SPI bus
ret = esp.spi_bus_initialize(self.spihost, buscfg, 1)
if ret != 0: raise RuntimeError("Failed initializing SPI bus")
# Attach the LCD to the SPI bus
ptr_to_spi = esp.C_Pointer()
ret = esp.spi_bus_add_device(self.spihost, devcfg, ptr_to_spi)
if ret != 0: raise RuntimeError("Failed adding SPI device")
self.spi = ptr_to_spi.ptr_val
self.bytes_transmitted = 0
completed_spi_transaction = esp.spi_transaction_t()
cast_spi_transaction_instance = esp.spi_transaction_t.cast_instance
def post_isr(arg):
reported_transmitted = self.bytes_transmitted
if reported_transmitted > 0:
print('- Completed DMA of %d bytes (mem_free=0x%X)' %
(reported_transmitted, gc.mem_free()))
self.bytes_transmitted -= reported_transmitted
# Called in ISR context!
def flush_isr(spi_transaction_ptr):
lv.disp_flush_ready(self.disp_drv)
# esp.spi_device_release_bus(self.spi)
esp.get_ccount(self.end_time_ptr)
# cast_spi_transaction_instance(completed_spi_transaction, spi_transaction_ptr)
# self.bytes_transmitted += completed_spi_transaction.length
# try:
# micropython.schedule(post_isr, None)
# except RuntimeError:
# pass
self.spi_callbacks = esp.spi_transaction_set_cb(None, flush_isr)
######################################################
trans = esp.spi_transaction_t() # .cast(
# esp.heap_caps_malloc(
# esp.spi_transaction_t.SIZE, esp.CAP.DMA))
def spi_send(self, data):
self.trans.length = len(
data) * 8 # Length is in bytes, transaction length is in bits.
self.trans.tx_buffer = data # data should be allocated as DMA-able memory
self.trans.user = None
esp.spi_device_polling_transmit(self.spi, self.trans)
def spi_send_dma(self, data):
self.trans.length = len(
data) * 8 # Length is in bytes, transaction length is in bits.
self.trans.tx_buffer = data # data should be allocated as DMA-able memory
self.trans.user = self.spi_callbacks
esp.spi_device_queue_trans(self.spi, self.trans, -1)
######################################################
######################################################
trans_buffer_len = const(16)
trans_buffer = esp.heap_caps_malloc(trans_buffer_len, esp.CAP.DMA)
cmd_trans_data = trans_buffer.__dereference__(1)
word_trans_data = trans_buffer.__dereference__(4)
def send_cmd(self, cmd):
esp.gpio_set_level(self.dc, 0) # Command mode
self.cmd_trans_data[0] = cmd
self.spi_send(self.cmd_trans_data)
def send_data(self, data):
esp.gpio_set_level(self.dc, 1) # Data mode
if len(data) > self.trans_buffer_len:
raise RuntimeError('Data too long, please use DMA!')
trans_data = self.trans_buffer.__dereference__(len(data))
trans_data[:] = data[:]
self.spi_send(trans_data)
def send_trans_word(self):
esp.gpio_set_level(self.dc, 1) # Data mode
self.spi_send(self.word_trans_data)
def send_data_dma(self,
data): # data should be allocated as DMA-able memory
esp.gpio_set_level(self.dc, 1) # Data mode
self.spi_send_dma(data)
######################################################
def init(self):
self.disp_spi_init()
# Initialize non-SPI GPIOs
esp.gpio_pad_select_gpio(self.dc)
esp.gpio_pad_select_gpio(self.rst)
if self.backlight != -1: esp.gpio_pad_select_gpio(self.backlight)
if self.power != -1: esp.gpio_pad_select_gpio(self.power)
esp.gpio_set_direction(self.dc, esp.GPIO_MODE.OUTPUT)
esp.gpio_set_direction(self.rst, esp.GPIO_MODE.OUTPUT)
if self.backlight != -1:
esp.gpio_set_direction(self.backlight, esp.GPIO_MODE.OUTPUT)
if self.power != -1:
esp.gpio_set_direction(self.power, esp.GPIO_MODE.OUTPUT)
# Power the display
if self.power != -1:
esp.gpio_set_level(self.power, 0)
esp.task_delay_ms(100)
# Reset the display
esp.gpio_set_level(self.rst, 0)
esp.task_delay_ms(100)
esp.gpio_set_level(self.rst, 1)
esp.task_delay_ms(100)
# Send all the commands
for cmd in self.init_cmds:
self.send_cmd(cmd['cmd'])
self.send_data(cmd['data'])
if 'delay' in cmd:
esp.task_delay_ms(cmd['delay'])
print("ILI9341 initialization completed")
# Enable backlight
if self.backlight != -1:
print("Enable backlight")
esp.gpio_set_level(self.backlight, 0)
######################################################
start_time_ptr = esp.C_Pointer()
end_time_ptr = esp.C_Pointer()
flush_acc_setup_cycles = 0
flush_acc_dma_cycles = 0
def flush(self, disp_drv, area, color_p):
if self.end_time_ptr.int_val and self.end_time_ptr.int_val > self.start_time_ptr.int_val:
self.flush_acc_dma_cycles += self.end_time_ptr.int_val - self.start_time_ptr.int_val
esp.get_ccount(self.start_time_ptr)
# esp.spi_device_acquire_bus(self.spi, esp.ESP.MAX_DELAY)
# Column addresses
self.send_cmd(0x2A)
self.word_trans_data[0] = (area.x1 >> 8) & 0xFF
self.word_trans_data[1] = area.x1 & 0xFF
self.word_trans_data[2] = (area.x2 >> 8) & 0xFF
self.word_trans_data[3] = area.x2 & 0xFF
self.send_trans_word()
# Page addresses
self.send_cmd(0x2B)
self.word_trans_data[0] = (area.y1 >> 8) & 0xFF
self.word_trans_data[1] = area.y1 & 0xFF
self.word_trans_data[2] = (area.y2 >> 8) & 0xFF
self.word_trans_data[3] = area.y2 & 0xFF
self.send_trans_word()
# Memory write by DMA, disp_flush_ready when finished
self.send_cmd(0x2C)
size = (area.x2 - area.x1 + 1) * (area.y2 - area.y1 + 1)
data_view = color_p.__dereference__(size * lv.color_t.SIZE)
esp.get_ccount(self.end_time_ptr)
if self.end_time_ptr.int_val > self.start_time_ptr.int_val:
self.flush_acc_setup_cycles += self.end_time_ptr.int_val - self.start_time_ptr.int_val
esp.get_ccount(self.start_time_ptr)
self.send_data_dma(data_view)
######################################################
monitor_acc_time = 0
monitor_acc_px = 0
monitor_count = 0
cycles_in_ms = esp.esp_clk_cpu_freq() // 1000
def monitor(self, disp_drv, time, px):
self.monitor_acc_time += time
self.monitor_acc_px += px
self.monitor_count += 1
def stat(self):
if self.monitor_count == 0:
return None
time = self.monitor_acc_time // self.monitor_count
setup = self.flush_acc_setup_cycles // (self.monitor_count *
self.cycles_in_ms)
dma = self.flush_acc_dma_cycles // (self.monitor_count *
self.cycles_in_ms)
px = self.monitor_acc_px // self.monitor_count
self.monitor_acc_time = 0
self.monitor_acc_px = 0
self.monitor_count = 0
self.flush_acc_setup_cycles = 0
self.flush_acc_dma_cycles = 0
return time, setup, dma, px
def __init__(
self,
m5stack,
miso=5,
mosi=18,
clk=19,
cs=13,
dc=12,
backlight_on=0,
power_on=0,
spihost=esp.HSPI_HOST,
mhz=40,
factor=4,
hybrid=True,
width=320,
height=240,
colormode=COLOR_MODE_BGR,
rot=LANDSCAPE,
invert=False,
double_buffer=True,
half_duplex=True,
display_type=0,
debug=False,
):
# Initializations
self.debug = debug
self.width = width
self.height = height
self.m5stack = m5stack
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.backlight_on = backlight_on
self.power_on = power_on
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.half_duplex = half_duplex
self.buf_size = (self.width * self.height * lv.color_t.SIZE) // factor
if invert:
self.init_cmds.append({"cmd": 0x21})
self.init()
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.MALLOC_CAP.DMA)
self.buf2 = (esp.heap_caps_malloc(self.buf_size, esp.MALLOC_CAP.DMA)
if double_buffer else None)
if self.buf1 and self.buf2:
if self.debug:
print("Double buffer")
elif self.buf1:
if self.debug:
print("Single buffer")
else:
raise RuntimeError(
"Not enough DMA-able memory to allocate display buffer")
self.disp_buf = lv.disp_buf_t()
self.disp_drv = lv.disp_drv_t()
self.disp_buf.init(self.buf1, self.buf2,
self.buf_size // lv.color_t.SIZE)
self.disp_drv.init()
self.disp_drv.user_data = {
"dc": self.dc,
"spi": self.spi,
"dt": self.display_type
}
self.disp_drv.buffer = self.disp_buf
self.disp_drv.flush_cb = (esp.ili9xxx_flush
if hybrid and hasattr(esp, "ili9xxx_flush")
else self.flush)
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
self.disp_drv.register()
def __init__(self,
miso=5,
mosi=18,
clk=19,
cs=13,
dc=12,
rst=4,
power=14,
backlight=15,
backlight_on=0,
power_on=0,
spihost=esp.HSPI_HOST,
mhz=40,
factor=4,
hybrid=True,
width=240,
height=320,
colormode=COLOR_MODE_BGR,
rot=PORTRAIT,
invert=False,
double_buffer=True,
half_duplex=True,
display_type=0,
asynchronous=False,
initialize=True):
# Initializations
self.asynchronous = asynchronous
self.initialize = initialize
self.width = width
self.height = height
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.rst = rst
self.power = power
self.backlight = backlight
self.backlight_on = backlight_on
self.power_on = power_on
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.half_duplex = half_duplex
self.buf_size = (self.width * self.height * lv.color_t.SIZE) // factor
if invert:
self.init_cmds.append({'cmd': 0x21})
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.MALLOC_CAP.DMA)
self.buf2 = esp.heap_caps_malloc(
self.buf_size, esp.MALLOC_CAP.DMA) if double_buffer else None
if self.buf1 and self.buf2:
print("Double buffer")
elif self.buf1:
print("Single buffer")
else:
raise RuntimeError(
"Not enough DMA-able memory to allocate display buffer")
self.disp_buf = lv.disp_buf_t()
self.disp_drv = lv.disp_drv_t()
self.disp_buf.init(self.buf1, self.buf2,
self.buf_size // lv.color_t.SIZE)
self.disp_drv.init()
self.disp_spi_init()
self.disp_drv.user_data = {
'dc': self.dc,
'spi': self.spi,
'dt': self.display_type
}
self.disp_drv.buffer = self.disp_buf
self.disp_drv.flush_cb = esp.ili9xxx_flush if hybrid and hasattr(
esp, 'ili9xxx_flush') else self.flush
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
if self.initialize:
self.init()
def __init__(self,
m5stack=M5Stack(),
miso=5,
mosi=18,
clk=19,
cs=13,
dc=12,
backlight=100,
backlight_on=1,
power_on=1,
spihost=esp.HSPI_HOST,
mhz=40,
factor=4,
hybrid=True,
width=240,
height=320,
start_x=0,
start_y=0,
invert=False,
double_buffer=True,
half_duplex=True,
display_type=0,
asynchronous=False,
initialize=True):
# Initializations
if not lv.is_initialized():
lv.init()
self.asynchronous = asynchronous
self.initialize = initialize
self.m5stack = m5stack
self.width = width
self.height = height
self.start_x = start_x
self.start_y = start_y
self.miso = miso
self.mosi = mosi
self.clk = clk
self.cs = cs
self.dc = dc
self.backlight = backlight
self.backlight_on = backlight_on
self.power_on = power_on
self.spihost = spihost
self.mhz = mhz
self.factor = factor
self.hybrid = hybrid
self.half_duplex = half_duplex
self.display_type = display_type
self.buf_size = (self.width * self.height *
lv.color_t.__SIZE__) // factor
if invert:
self.init_cmds.append({'cmd': 0x21})
# Register display driver
self.buf1 = esp.heap_caps_malloc(self.buf_size, esp.MALLOC_CAP.DMA)
self.buf2 = esp.heap_caps_malloc(
self.buf_size, esp.MALLOC_CAP.DMA) if double_buffer else None
if self.buf1 and self.buf2:
print("Double buffer")
elif self.buf1:
print("Single buffer")
else:
raise RuntimeError(
"Not enough DMA-able memory to allocate display buffer")
self.disp_buf = lv.disp_draw_buf_t()
self.disp_drv = lv.disp_drv_t()
self.disp_buf.init(self.buf1, self.buf2,
self.buf_size // lv.color_t.__SIZE__)
self.disp_drv.init()
self.disp_spi_init()
self.disp_drv.user_data = {
'dc': self.dc,
'spi': self.spi,
'dt': self.display_type,
'start_x': self.start_x,
'start_y': self.start_y
}
self.disp_drv.draw_buf = self.disp_buf
self.disp_drv.flush_cb = esp.ili9xxx_flush if hybrid and hasattr(
esp, 'ili9xxx_flush') else self.flush
self.disp_drv.monitor_cb = self.monitor
self.disp_drv.hor_res = self.width
self.disp_drv.ver_res = self.height
if self.initialize:
self.init()
if not lv_utils.event_loop.is_running():
self.event_loop = lv_utils.event_loop(
asynchronous=self.asynchronous)
