infill_holes,
pattern_lines=line_pattern(
d,
angle=45 if h % 0.4 > 0.15 else -45))
e, commands = print_layer(infill_lines,
e=e,
h=h,
start_point=(0, 0),
layer_height=layer_height)
f.write(commands)
# print("e after Infill: {}".format(e))
e, cmd = retract(e, retract_volume=9, filament_d=1.75)
f.write(cmd + "\n")
f.write(travel((30 + 3 * 30, 30 + 2 * 30, h)) + "\n")
e, cmd = resume(e, retract_volume=9, filament_d=1.75)
f.write(cmd + "\n")
e, cmd = print_move((30 + 3 * 30, 30 + 2 * 30, h),
(30 + 3 * 30 + 10, 30 + 2 * 30, h),
old_e=e,
h=layer_height)
f.write(cmd + "\n")
f.write(travel((30 + 3 * 30 + 10, 30 + 2 * 30 + 10, h)) + "\n")
f.write(travel((30 + 3 * 30, 30 + 2 * 30 + 10, h)) + "\n")
f.write(travel((30 + 3 * 30, 30 + 2 * 30, h)) + "\n")
e, cmd = retract(e, retract_volume=9, filament_d=1.75)
f.write(cmd + "\n")
print("Height {} sliced.".format(h))
h += 0.2
f.write(stop_sequence())
print("File {0} written.".format(filename))
from __future__ import division, print_function, unicode_literals
from gcodehelpers import print_move, travel, retract, resume, start_sequence, stop_sequence, fan_on
if __name__ == "__main__":
filename = "retract_grid.gcode"
with open(filename, 'w') as f:
f.write(start_sequence() + "\n")
e = 0.0
h = 0.3
f.write(travel((65, 65, h)) + "\n")
points = [(65, 65), (175, 65), (175, 175), (65, 175), (65, 65),
(64.6, 64.6), (174.6, 64.6), (174.6, 174.6), (64.6, 174.6),
(64.6, 64.6)]
old_x, old_y = points[0]
for x, y in points:
e, command = print_move((old_x, old_y, h), (x, y, h), old_e=e)
old_x, old_y = x, y
f.write(command + "\n")
f.write(travel((70, 70, h)) + "\n")
for i in range(99):
for j in range(10):
e, command = print_move((70 + j * 10, 70, h),
(70 + j * 10, 80, h),
old_e=e)
f.write(command + "\n")
e, command = retract(old_e=e, retract_volume=j)
f.write(command + "\n")
f.write(travel((70 + j * 10, 90, h)) + "\n")
e, command = resume(old_e=e, retract_volume=j)
f.write(command + "\n")
e, command = print_move((70 + j * 10, 90, h),
from __future__ import division, print_function, unicode_literals
from gcodehelpers import print_move, travel, start_sequence, stop_sequence, fan_on
if __name__ == "__main__":
filename = "calibration_box.gcode"
with open(filename, 'w') as f:
f.write(start_sequence() + "\n")
e = 0.0
h = 0.3
f.write(travel((65, 65, h)) + "\n")
points = [(65, 65), (105, 65), (105, 105), (65, 105), (65, 65),
(64.6, 64.6), (105.4, 64.6), (105.4, 105.4), (64.6, 105.4),
(64.6, 64.6)]
old_x, old_y = points[0]
for x, y in points:
e, command = print_move((old_x, old_y, h), (x, y, h), old_e=e)
old_x, old_y = x, y
f.write(command + "\n")
f.write(travel((70, 70, h)) + "\n")
points = [(70, 70), (100, 70), (100, 100), (70, 100), (70, 70)]
for i in range(99):
for x, y in points:
e, command = print_move((old_x, old_y, h), (x, y, h), old_e=e)
old_x, old_y = x, y
f.write(command + "\n")
h += 0.2
if i == 0:
f.write(fan_on() + "\n")
f.write(travel((70, 70, h)) + "\n")
f.write(stop_sequence())
print("File {0} written.".format(filename))
from gcodehelpers import print_move, travel, start_sequence, stop_sequence, get_line_distance
if __name__ == "__main__":
filename = "first_layer_carpet.gcode"
with open(filename, 'w') as f:
f.write(start_sequence() + "\n")
e = 0.0
h = 0.3
w = 0.42
x_offset = 65
y_offset = 65
carpet_width = 40
carpet_length = 60
f.write(travel((x_offset, y_offset, h)) + "\n")
y = y_offset
while y <= y_offset + carpet_length - 2 * get_line_distance(w, h, 0.4):
e, command = print_move((x_offset, y, h),
(x_offset + carpet_width, y, h),
old_e=e)
f.write(command + "\n")
y = y + get_line_distance(w, h, 0.4)
f.write(travel((x_offset + carpet_width, y, h)) + "\n")
e, command = print_move((x_offset + carpet_width, y, h),
(x_offset, y, h),
old_e=e)
f.write(command + "\n")
y = y + get_line_distance(w, h, 0.4)
f.write(travel((x_offset, y, h)) + "\n")
f.write(stop_sequence())
print("File {0} written.".format(filename))
if __name__ == "__main__":
filename = "acceleration_test.gcode"
with open(filename, 'w') as f:
f.write(start_sequence() + "\n")
e = 0.0
h = 0.3
filament_d = 1.75
f.write(travel((65, 65, h)) + "\n")
points = [(65, 65), (105, 65), (105, 105), (65, 105), (65, 65),
(64.6, 64.6), (104.6, 64.6), (104.6, 104.6), (64.6, 104.6),
(64.6, 64.6)]
old_x, old_y = points[0]
for x, y in points:
e, command = print_move((old_x, old_y, h), (x, y, h),
old_e=e,
filament_d=filament_d)
old_x, old_y = x, y
f.write(command + "\n")
f.write("G0 X70 Y70 Z0.3\n")
speed = 2000
acceleration = 300
f.write("M201 X" + str(acceleration) + " Y" + str(acceleration) + "\n")
points = [(70, 70), (100, 70), (100, 100), (70, 100), (70, 70)]
for i in range(399):
for x, y in points:
e, command = print_move((old_x, old_y, h), (x, y, h),
old_e=e,
filament_d=filament_d,
speed=speed)
old_x, old_y = x, y