def alarmsniffer():
alarm_codes_ein = ['1361', '4433', '5201', '5393']
alarm_codes_aus = ['1364', '4436', '5204', '5396']
receiver = RCSwitchReceiver()
receiver.enableReceive(2)
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if (received_value):
if any(str(received_value) in s for s in alarm_codes_ein):
alarm('EIN')
subprocess.call("sh monitor_on.sh &> /dev/null",
shell=True)
if any(str(received_value) in s for s in alarm_codes_aus):
alarm('AUS')
receiver.resetAvailable()
time.sleep(.5)
class RCSwitch(Switch):
def __init__(self, triggervalue, shutdownvalue, exitvalue):
self.receiver = RCSwitchReceiver()
self.receiver.enableReceive(2)
self.triggervalue = triggervalue
self.shutdownvalue = shutdownvalue
self.exitvalue = exitvalue
def get_switch_state(self):
if self.receiver.available():
value = self.receiver.getReceivedValue()
self.receiver.resetAvailable()
return {
self.triggervalue: SwitchState.TRIGGER,
self.shutdownvalue: SwitchState.SHUTDOWN,
self.exitvalue: SwitchState.EXIT
}.get(value, SwitchState.NONE)
return SwitchState.NONE
class RCSwitch(Switch):
def __init__(self, triggervalue, shutdownvalue, exitvalue):
self.receiver = RCSwitchReceiver()
self.receiver.enableReceive(2)
self.triggervalue = triggervalue
self.shutdownvalue = shutdownvalue
self.exitvalue = exitvalue
def get_switch_state(self):
if self.receiver.available():
value = self.receiver.getReceivedValue()
self.receiver.resetAvailable()
return {
self.triggervalue: SwitchState.TRIGGER,
self.shutdownvalue: SwitchState.SHUTDOWN,
self.exitvalue: SwitchState.EXIT
}.get(value, SwitchState.NONE)
return SwitchState.NONE
def run_receiver():
""" Setup the Raspberry Pi as receiver, listen for transmitted values,
display every received number as binary < 256 if the display is attached.
Prints the received value, bit length and protocol to the terminal. """
receiver = RCSwitchReceiver()
receiver.enableReceive(2)
while True:
print 'Listening...'
sleep(0.5)
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
display_number(received_value % 256, True)
print("Value: %s | Bit: %s | Protocol: %s" %
(received_value, receiver.getReceivedBitlength(),
receiver.getReceivedProtocol()))
receiver.resetAvailable()
class Receiver433Manager(threading.Thread):
def __init__(self, shared_queue):
super(Receiver433Manager, self).__init__()
# shared queue to send data (received UID)to the main thread
self.shared_queue = shared_queue
# init the lib
self.receiver = RCSwitchReceiver()
# WiringPi 2 = RPI pin 13 = GPIO 27
self.receiver.enableReceive(2)
# this is used to stop the arming thread
self.stop_event = threading.Event()
def run(self):
print "Starting receiver 433"
while not self.stop_event.is_set():
if self.receiver.available():
received_value = self.receiver.getReceivedValue()
if received_value:
print "Receiver 433; Received id: %s" % received_value
# send the value to the main thread
if self.shared_queue is not None:
self.shared_queue.put(received_value)
# wait before listen again
time.sleep(1)
self.receiver.resetAvailable()
# take a breath
time.sleep(0.1)
def stop(self):
"""
Stop the thread
:return:
"""
self.stop_event.set()
self.receiver.resetAvailable()
from pi_switch import RCSwitchReceiver
from Config import Config
#---------------------------------------------------------------------------#
# Configure receiver
#---------------------------------------------------------------------------#
receiver = RCSwitchReceiver()
receiver.enableReceive(Config.RPi_Pin_Receiver)
num = 0
#---------------------------------------------------------------------------#
# Loop and wait for commands
#---------------------------------------------------------------------------#
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
num += 1
print("Received[%s]:" % num)
print(received_value)
print("%s / %s bit" %
(received_value, receiver.getReceivedBitlength()))
print("Protocol: %s" % receiver.getReceivedProtocol())
print("")
receiver.resetAvailable()
prevHum=0
def onConnect(client, userdata, flags, rc):
print("Connected with result code "+str(rc))
mqttClient = mqtt.Client("c3")
mqttClient.on_connect = onConnect
#mqttClient.connect("54.187.15.61",1883)
mqttClient.connect("54.67.96.20",1883)
message={}
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
num += 1
print("Received[%s]:" % num)
print(received_value)
print("%s / %s bit" % (received_value, receiver.getReceivedBitlength()))
print("Protocol: %s" % receiver.getReceivedProtocol())
print("")
lst = [int(i) for i in str(received_value)]
print(lst[1])
try:
checkSum=lst[0]+lst[1]+lst[2]+lst[3]+lst[4]
checkSum=checkSum*lst[4]
except:
