class ADC16():
def __init__(self):
self.spi = SPI(1)
self.SCK=Pin('PA5',Pin.OUT)
self.DO = Pin('PA6',Pin.OUT)
self.DI = Pin('PA7',Pin.OUT)
self.CS = Pin('PA4',Pin.OUT)
self.RESET = Pin('PC5',Pin.OUT)
self.DRDY = Pin('PC4',Pin.OUT)
self.bsp_DelayMS(10)
# self.TM7705_ResetHard() #/* 硬件复位 */
# #/*
# # 在接口序列丢失的情况下，如果在DIN 高电平的写操作持续了足够长的时间（至少 32个串行时钟周期），
# # TM7705 将会回到默认状态。
# #*/
# self.bsp_DelayMS(5)
# self.TM7705_SyncSPI() #/* 同步SPI接口时序 */
# self.bsp_DelayMS(5)
# # /* 配置时钟寄存器 */
# self.TM7705_WriteByte(REG_CLOCK | WRITE | CH_1) # /* 先写通信寄存器，下一步是写时钟寄存器 */
# self.TM7705_WriteByte(CLKDIS_0 | CLK_4_9152M | FS_50HZ) #/* 刷新速率50Hz */
# #//TM7705_WriteByte(CLKDIS_0 | CLK_4_9152M | FS_500HZ);# /* 刷新速率500Hz */
# # /* 每次上电进行一次自校准 */
# self.TM7705_CalibSelf(1) #/* 内部自校准 CH1 */
# self.bsp_DelayMS(5)
def bsp_DelayMS(self,t):
time.sleep_ms(t)
def TM7705_ResetHard(self):
self.RESET.on()
self.bsp_DelayMS(1)
self.RESET.off()
self.bsp_DelayMS(2)
self.RESET.on()
self.bsp_DelayMS(1)
def TM7705_SyncSPI(self):
self.CS.off()
self.TM7705_Send8Bit(0xFF)
self.TM7705_Send8Bit(0xFF)
self.TM7705_Send8Bit(0xFF)
self.TM7705_Send8Bit(0xFF)
self.CS.on()
def TM7705_Send8Bit(self,data):
data = data%256
self.spi.write(struct.pack('B',data))
def TM7705_WriteByte(self,data):
self.CS.off()
self.TM7705_Send8Bit(data)
self.CS.on()
def TM7705_Write3Byte(self,data):
self.CS.off()
self.TM7705_Send8Bit(data>>16)
self.TM7705_Send8Bit(data>>8)
self.TM7705_Send8Bit(data)
self.CS.on()
# def TM7705_ReadByte(self):
# read = 0
# self.CS.off()
# read = self.spi.read()
# print(read)
# self.CS.on()
# return read
# def TM7705_Read2Byte(self):
# self.TM7705_ReadByte()
# def TM7705_Read3Byte(self):
# self.TM7705_ReadByte()
# ##################################待更改
def TM7705_WaitDRDY(self):
while (self.DRDY.value()):
time.sleep_ms(200)
#等待校准
def TM7705_WriteReg(self,_RegID,_RegValue):
bits = 0
if _RegID == REG_COMM or _RegID ==REG_SETUP or _RegID == REG_CLOCK:
bits = 8
elif _RegID ==REG_ZERO_CH1 or _RegID ==REG_FULL_CH1 or _RegID ==REG_ZERO_CH2 or _RegID ==REG_FULL_CH2 :
bits=24
self.TM7705_WriteByte(_RegID | WRITE)
if bits==8:
self.TM7705_WriteByte(_RegValue)
else :
self.TM7705_Write3Byte(_RegValue)
def TM7705_CalibSelf(self,_ch):
if _ch==1:
# /* 自校准CH1 */
self.TM7705_WriteByte(REG_SETUP | WRITE | CH_1)#; #/* 写通信寄存器，下一步是写设置寄存器，通道1 */
self.TM7705_WriteByte(MD_CAL_SELF | __CH1_GAIN_BIPOLAR_BUF | FSYNC_0)#;#/* 启动自校准 */
self.TM7705_WaitDRDY()#; /* 等待内部操作完成 --- 时间较长，约180ms */
elif _ch == 2:
# /* 自校准CH2 */
self.TM7705_WriteByte(REG_SETUP | WRITE | CH_2)#; /* 写通信寄存器，下一步是写设置寄存器，通道2 */
self.TM7705_WriteByte(MD_CAL_SELF | __CH2_GAIN_BIPOLAR_BUF | FSYNC_0)# /* 启动自校准 */
self.TM7705_WaitDRDY()
#####read adc
def TM7705_ReadAdc(self,_ch):
read = 0
for ii in range(2):
self.TM7705_WaitDRDY()
if _ch == 1:
self.TM7705_WriteByte(0x38)
elif _ch == 2:
self.TM7705_WriteByte(0x39)
#read2byte
read = self.spi.read()
return read
print(spi)
spi = SPI(0, SPI.MASTER, baudrate=5000000, bits=32, polarity=1, phase=0)
print(spi)
spi = SPI(0, SPI.MASTER, baudrate=10000000, polarity=1, phase=1)
print(spi)
spi.init(baudrate=20000000, polarity=0, phase=0)
print(spi)
spi=SPI()
print(spi)
SPI(mode=SPI.MASTER)
SPI(mode=SPI.MASTER, pins=spi_pins)
SPI(id=0, mode=SPI.MASTER, polarity=0, phase=0, pins=('GP14', 'GP16', 'GP15'))
SPI(0, SPI.MASTER, polarity=0, phase=0, pins=('GP31', 'GP16', 'GP15'))
spi = SPI(0, SPI.MASTER, baudrate=10000000, polarity=0, phase=0, pins=spi_pins)
print(spi.write('123456') == 6)
buffer_r = bytearray(10)
print(spi.readinto(buffer_r) == 10)
print(spi.readinto(buffer_r, write=0x55) == 10)
read = spi.read(10)
print(len(read) == 10)
read = spi.read(10, write=0xFF)
print(len(read) == 10)
buffer_w = bytearray([1, 2, 3, 4, 5, 6, 7, 8, 9, 0])
print(spi.write_readinto(buffer_w, buffer_r) == 10)
print(buffer_w == buffer_r)
# test all polaritiy and phase combinations
spi.init(polarity=1, phase=0, pins=None)
buffer_r = bytearray(10)
spi.write_readinto(buffer_w, buffer_r)
print(spi)
spi = SPI(0, SPI.MASTER, baudrate=5000000, bits=32, polarity=1, phase=0)
print(spi)
spi = SPI(0, SPI.MASTER, baudrate=10000000, polarity=1, phase=1)
print(spi)
spi.init(baudrate=20000000, polarity=0, phase=0)
print(spi)
spi = SPI()
print(spi)
SPI(mode=SPI.MASTER)
SPI(mode=SPI.MASTER, pins=spi_pins)
SPI(id=0, mode=SPI.MASTER, polarity=0, phase=0, pins=('GP14', 'GP16', 'GP15'))
SPI(0, SPI.MASTER, polarity=0, phase=0, pins=('GP31', 'GP16', 'GP15'))
spi = SPI(0, SPI.MASTER, baudrate=10000000, polarity=0, phase=0, pins=spi_pins)
print(spi.write('123456') == 6)
buffer_r = bytearray(10)
print(spi.readinto(buffer_r) == 10)
print(spi.readinto(buffer_r, write=0x55) == 10)
read = spi.read(10)
print(len(read) == 10)
read = spi.read(10, write=0xFF)
print(len(read) == 10)
buffer_w = bytearray([1, 2, 3, 4, 5, 6, 7, 8, 9, 0])
print(spi.write_readinto(buffer_w, buffer_r) == 10)
print(buffer_w == buffer_r)
# test all polaritiy and phase combinations
spi.init(polarity=1, phase=0, pins=None)
buffer_r = bytearray(10)
spi.write_readinto(buffer_w, buffer_r)
import sensor, image, time
import pyb
from pyb import SPI
# Camera/Hardware Objects:
fmt = sensor.RGB565
res = sensor.QVGA
led1 = pyb.LED(1)
led2 = pyb.LED(2)
# SPI bus for lighting
spi = SPI(2, SPI.MASTER, 500000, polarity=1, phase=0, crc=None)
ledreset = bytearray(24)
# Reset the LED strip
spi.write(ledreset)
# Turn on Green lighting:
ledgreen = bytearray(24)
for ii in range(0, len(ledgreen)):
ledgreen[ii] = 128
intensity = 110
for ii in range(0, 8):
ledgreen[ii * 3] = 128 + intensity
spi.write(ledgreen)
spi.write(ledreset)
# Get Camera ID:
