help="Battery type(1=Sealed,2=Gel,3=Flooded)",
type=int,
dest="battery_type",
default=None)
parser.add_argument("-c",
"--battery-capacity",
help="Battery capacity in Ah",
type=int,
dest="battery_capacity",
default=None)
args = parser.parse_args()
client = EPsolarTracerClient(port="/dev/ttyXRUSB0")
if args.battery_type is None:
print "Battery type: %s" % (
battery_types[client.read_input(REG_BATTERY_TYPE).value])
else:
if args.battery_type in (1, 2, 3):
client.write_output(REG_BATTERY_TYPE, args.battery_type)
print "Battery type set to %s" % (battery_types[args.battery_type])
else:
print "Invalid battery type"
if args.battery_capacity is None:
print "Battery capacity: %dAh" % (
client.read_input(REG_BATTERY_CAPACITY).value)
else:
client.write_output(REG_BATTERY_CAPACITY, args.battery_capacity)
print "Battery capacity set to %dAh" % (args.battery_capacity)
# 0000H Manual Control
# 0001H Light ON/OFF
# 0002H Light ON+ Timer/
# 0003H Time Control
loadCtrlMode = 0x0003
#response = client.client.write_registers(loadCtrlModesAddr, loadCtrlMode, unit = client.unit)
#print "Write result: " + str(vars(response))
response = client.read_input("Load controling modes")
print "Load controlling mode: " + hex(response.value)
#response = client.write_output("Turn on timing 1 hour",9)
#response = client.write_output("Turn on timing 1 min",30)
response = client.write_output("Turn off timing 1 hour", 16)
response = client.write_output("Turn off timing 1 min", 0)
#response = client.write_output("Turn on timing 2 hour",9)
#response = client.write_output("Turn on timing 2 min",30)
response = client.write_output("Turn off timing 2 hour", 16)
response = client.write_output("Turn off timing 2 min", 0)
print "Load Time Contolled #1"
second = client.read_input("Turn on timing 1 sec").value
minute = client.read_input("Turn on timing 1 min").value
hour = client.read_input("Turn on timing 1 hour").value
print " ON: %02d:%02d:%02d" % (int(hour), int(minute), int(second))
second = client.read_input("Turn off timing 1 sec").value
minute = client.read_input("Turn off timing 1 min").value
hour = client.read_input("Turn off timing 1 hour").value
print " OFF: %02d:%02d:%02d" % (int(hour), int(minute), int(second))
from pyepsolartracer.client import EPsolarTracerClient
from pyepsolartracer.registers import registers, coils
from pymodbus.client.sync import ModbusSerialClient as ModbusClient
# configure the client logging
import logging
logging.basicConfig()
log = logging.getLogger()
log.setLevel(logging.INFO)
serialclient = ModbusClient(method='rtu',
port='/dev/ttyXRUSB0',
baudrate=115200,
stopbits=1,
bytesize=8,
timeout=0.05)
client = EPsolarTracerClient(serialclient=serialclient)
client.connect()
print client.write_output("Manual control the load", True)
value = client.read_input("Manual control the load")
print value
client.close()
log.setLevel(logging.INFO)
# choose the serial client
serialclient = ModbusClient(method='rtu',
port='/dev/ttyXRUSB0',
baudrate=115200,
stopbits=1,
bytesize=8,
timeout=1)
#serialclient = None
# choose the serial client
client = EPsolarTracerClient(serialclient=serialclient)
client.connect()
client.write_output("Battery Capacity", 408)
# 400 if parellelized
client.write_output("Battery Type", 0x0000)
# = custom
client.close()
client.connect()
#client.write_output("High Volt.disconnect", 15.0)
client.write_output("Charging limit voltage", 14.6)
client.write_output("Over voltage reconnect", 14.8)
client.write_output("Equalization voltage", 14.6) # not required with agm
client.write_output("Boost voltage", 13.8)
client.write_output("Float voltage", 13.4)
client.write_output("Boost reconnect voltage", 13.2)
client.write_output("Low voltage reconnect", 12.2)
timeout=1)
#serialclient = None
client = EPsolarTracerClient(serialclient=serialclient)
client.connect()
response = client.read_device_info()
#print "Manufacturer:", repr(response.information[0])
#print "Model:", repr(response.information[1])
#print "Version:", repr(response.information[2])
#response = client.read_input("Charging equipment rated input voltage")
#print str(response)
vlist = []
for reg in Jregisters:
#print
print reg.address
value = client.read_input(reg.name)
vlist.append(value)
#print value
if reg.address == 36885:
X = value.value + 1
print reg.name
print client.write_output(reg.name, X)
print ",".join(map(str, vlist))
client.close()