if isinstance(ts.GetMeasureUnit(), LeicaTPS1200):
p = GetInt("Prism number (-1 for none) ", p)
if p >= 0:
ts.SetPrismType(p)
else:
pc = -99
atr = 0 if p == 2 else 1
else:
pc = GetFloat("Prism constant [mm] (-99 for none) ",
pc * 1000) / 1000.0
if pc > -99:
ts.SetPc(pc)
#pc = -99
atr = 0 if pc == 0.00344 else 1
print(ts.GetPc())
ts.SetATR(atr)
raw_input("Target on prism and press enter")
if atr:
res = ts.MoveRel(Angle(0), Angle(0), atr)
if 'errorCode' in res or ts.measureIface.state != ts.measureIface.IF_OK:
print("Cannot target on prism")
ts.measureIface.state = ts.measureIface.IF_OK
continue
res = ts.Measure()
obs = ts.GetMeasure()
obs['id'] = t_id
geo_wrt.WriteData(obs)
coo = ts.Coords()
coo['id'] = t_id
if pc > -99:
coo['pc'] = pc
filt=['id', 'hz', 'v', 'distance', 'east', 'north', 'elev'],
fname=sys.argv[5],
mode='a',
sep=';')
else:
wrt = EchoWriter()
ts = TotalStation("Leica", mu, iface)
slopeDist = 0
if edm not in mu.edmModes:
edm = 'FAST'
ts.SetEDMMode(edm)
# initialize instrument and variables
if mode > 0:
ts.SetLock(0)
ts.SetATR(1)
ts.MoveRel(Angle(0), Angle(0), 1)
ts.Measure()
measurement = ts.GetMeasure()
if 'distance' in measurement:
slopeDist = measurement['distance']
if mode in (3, 4, 5):
ts.SetLock(1)
ts.LockIn()
if mode == 5:
last_hz = measurement['hz'] # direction of last measured point
last_v = measurement['v']
prev_hz = measurement['hz'] # direction of last measured point
prev_v = measurement['v']
moving = True
#sys.exit(1)
# set port
port = 'COM5'
if len(sys.argv) > 4:
port = sys.argv[4]
iface = SerialIface("test", port)
# set output file name
fn = 'measmtrx.txt'
if len(sys.argv) > 5:
fn = sys.argv[5]
# write out measurements
wrt = FileWriter(angle='DEG', dist='.3f', fname=fn)
if wrt.GetState() != wrt.WR_OK:
sys.exit(-1) # open error
ts = TotalStation(stationtype, mu, iface, wrt)
ts.SetATR(0) # turn ATR off
ts.SetEDMMode('RLSTANDARD') # reflectorless distance measurement
ts.SetRedLaser(1) # turn red laser on
w = raw_input("Target on lower left corner and press Enter")
w1 = ts.GetAngles()
w = raw_input("Target on upper right corner and press Enter")
w2 = ts.GetAngles()
dh = (w2['hz'].GetAngle() - w1['hz'].GetAngle()) / dh_nr
dv = (w2['v'].GetAngle() - w1['v'].GetAngle()) / dv_nr
# measurement loops
for i in range(dh_nr + 1): # horizontal loop
measdir = i % 2 # check modulo
hz = Angle(w1['hz'].GetAngle() + i * dh, 'RAD')
for j in range(dv_nr + 1): # vertical loop
arange = PI2
if len(sys.argv) > 7:
arange = float(sys.argv[7]) / 360.0 * PI2
iface = SerialIface("rs-232", port) ## eomRead='\n'
wrt = CsvWriter(angle='DMS',
dist='.3f',
filt=['id', 'east', 'north', 'elev'],
fname='section.txt',
mode='w',
sep=';')
ts = TotalStation(stationtype, mu, iface)
if isinstance(mu, Trimble5500):
print("Set Trimble 550x to direct reflex (MNU 722)")
raw_input()
else:
ts.SetATR(0) # ATR mode off
ts.SetLock(0) # Lock mode off
ts.SetEDMMode("RLSTANDARD") # Reflectorless distance measurement
ts.SetRedLaser(1)
# Direction of the points to defining the plane
points = []
for i in range(numberOfPoints):
raw_input("Target on %d point and press enter" % (i + 1))
ts.Measure()
obs = ts.GetMeasure()
if ts.measureIface.state != ts.measureIface.IF_OK or \
'errorCode' in obs:
print('Start again!')
exit(1)
# Calculation of the directed coordinates according to the instrument's origin
