def doPath(X_offset=0, Y_offset=0): global toolPos_X, toolPos_Y, toolPos_Z, toolPos_F, X_dest, Y_dest, Z_dest, F_dest for path in etch_moves: toolRefresh = 0 toolPos_draw(toolPos_X, toolPos_Y, etching=0) cy.moveZ(Z_origin_offset + getZoffset(X_dest, Y_dest) + Z_global_offset + Zlift_milling, F_fastMove) # Raise and move to next point X_dest = path[0][0] + X_offset Y_dest = path[0][1] + Y_offset F_dest = F_fastMove print(" Traveling to: " + str([X_dest, Y_dest]) + " at Z:" + str(Z_global_offset + Zlift_milling)) cy.moveXY(X_dest, Y_dest, F_dest) toolPos_draw(X_dest, Y_dest, etching=0) Z_dest = path[0][2] if Z_dest > 0: F_dest = F_slowMove else: F_dest = path[0][ 3] # We set the original speed if it is etching/drill cy.moveZ( Z_dest + Z_origin_offset + getZoffset(X_dest, Y_dest) + Z_global_offset, F_dest) # print("Speed:",F_dest) print(" Etching at Z: " + str(Z_dest + Z_global_offset)) toolPos_X = X_dest toolPos_Y = Y_dest toolPos_Z = Z_dest # Not sure.. toolPos_F = F_dest # print(path) for coord in path[1:]: X_dest = coord[0] + X_offset Y_dest = coord[1] + Y_offset Z_dest = coord[2] F_dest = coord[3] distance = (X_dest - toolPos_X)**2 + (Y_dest - toolPos_Y)**2 if distance >= maxDistance: splitLongEtchMove(distance) if distance < minDistance and ( Z_dest - toolPos_Z )**2 < 0.001**2: # Make sure it is not a Z movement print("Ignoring " + str(distance**0.5) + "mm segment!") continue Z_real = Z_dest + Z_origin_offset + getZoffset( X_dest, Y_dest) + Z_global_offset cy.moveXYZ(X_dest, Y_dest, Z_real, F_dest) # print("Coords: Speed: " + str(F_dest)) toolPos_refresh(X_dest, Y_dest, etching=1) toolPos_X = X_dest toolPos_Y = Y_dest toolPos_Z = Z_dest toolPos_F = F_dest
def doPath(X_offset=0, Y_offset=0): global toolPos_X, toolPos_Y, toolPos_Z, toolPos_F, X_dest, Y_dest, Z_dest, F_dest for path in etch_moves : toolRefresh = 0 #toolPos_draw(toolPos_X, toolPos_Y, etching=0) cy.moveZ(Z_origin_offset+getZoffset(X_dest, Y_dest)+Z_global_offset+Zlift_milling,F_fastMove) # Raise and move to next point X_dest = path[0][0]+X_offset Y_dest = path[0][1]+Y_offset F_dest = F_fastMove print(" Traveling to: " + str([X_dest, Y_dest]) + " at Z:" + str(Z_global_offset+Zlift_milling) ) sys.stdout.flush() cy.moveXY(X_dest, Y_dest, F_dest) toolPos_draw(X_dest, Y_dest, etching=0) Z_dest = path[0][2] if Z_dest > 0: F_dest = F_slowMove else: F_dest = path[0][3] # We set the original speed if it is etching/drill cy.moveZ(Z_dest+Z_origin_offset+getZoffset(X_dest, Y_dest)+Z_global_offset,F_dest) # print("Speed:",F_dest) print(" Etching at Z: " + str(Z_dest+Z_global_offset) ) sys.stdout.flush() toolPos_X = X_dest toolPos_Y = Y_dest toolPos_Z = Z_dest # Not sure.. toolPos_F = F_dest # print(path) for coord in path[1:] : X_dest = coord[0]+X_offset Y_dest = coord[1]+Y_offset Z_dest = coord[2] F_dest = coord[3] distance = (X_dest-toolPos_X)**2+(Y_dest-toolPos_Y)**2 if distance >= maxDistance : splitLongEtchMove(distance) if distance < minDistance and (Z_dest-toolPos_Z)**2 < 0.001**2 : # Make sure it is not a Z movement print("Ignoring " + str(distance**0.5) + "mm segment!") continue Z_real = Z_dest+Z_origin_offset+getZoffset(X_dest, Y_dest)+Z_global_offset cy.moveXYZ(X_dest, Y_dest, Z_real, F_dest) # print("Coords: Speed: " + str(F_dest)) toolPos_refresh(X_dest, Y_dest, etching=1) toolPos_X = X_dest toolPos_Y = Y_dest toolPos_Z = Z_dest toolPos_F = F_dest sys.stdout.flush()