def asd():
GPIO.output(led1, GPIO.HIGH)
buz.on()
while (1):
a = GPIO.Input(but1)
print a
if (a == 1):
GPIO.output(led1, FALSE)
break
GPIO.output(led2, GPIO.HIGH) #digitalWrite(led2,HIGH);
while (1):
b = GPIO.Input(but2)
if (b == 1):
GPIO.output(led2, FALSE)
break
GPIO.output(led3, GPIO.HIGH) #digitalWrite(led3,HIGH);
while (1):
c = GPIO.Input(but3)
if (c == 1):
GPIO.output(led3, FALSE)
break
GPIO.output(led4, GPIO.HIGH) #digitalWrite(led3,HIGH);
while (1):
d = GPIO.Input(but4)
if (d == 1):
GPIO.output(led4, FALSE)
break
buz.off()
return 'asd'
def checkStatus():
# klic f() again in pollTime sekunde
threading.Timer(pollTime, checkStatus).start()
global count1
if (GPIO.Input(17)):
# Kopalnica je zaprta
updateHTML("Kopalnica1", 1)
count1 += pollTime
GPIO.output(25, GPIO.LOW)
else:
# Kopalnica je odprta
updateHTML("Kopalnica1", 0)
count1 = 0
GPIO.output(25, GPIO.HIGH)
if (count1 >= 600):
updateHTML("Kopalnica1", 3)
Created on Sun Dec 1 16:46:10 2019
@author: wpqld_000
"""
import time
import cv2 as cv # opencv
import RPi.GPIO as GPIO
ledPIN = 20 # led 용 핀 추후 수정 가능
# 모터 핀 바로 위에꺼
servoPIN = 21 # 21번 핀 사용 GND 옆
GPIO.setmode(GPIO.BCM)
GPIO.setup(servoPIN, GPIO.OUT)
GPIO.setup(ledPIN, GPIO.OUT) # 타이머 대용으로 쓸거므로 out
GPIO.Input()
p = GPIO.PWM(servoPIN, 50) # GPIO 17 als PWM mit 50Hz
l = GPIO.PWM(ledPIN, 50)
# 이게 왜 50부터 시작인지는 좀 봐야할거같
"""
GPIO.output(ledPIN,GPIO.HIGH)
GPIO.output(ledPIN,GPIO.LOW)
time.sleep(0.1)
"""
p.start(2.5) # Initialisierung 초기화
# 정확히는 현재 각도의 값을 몇으로 잡을 것인가를 정의
#우선 생각중인건 무한루프 돌리고,
@app.route('/')
def hello():
return render_template('main.html')#Return the main.html template to the web browser using the variables in the templateData dictionary
@app.route('/link',methods=["POST"])
def da():
hours=request.form['hours']
#minutes=request.form['mins']
#add to database
##compare
return ##reversewatch
@app.route('/asd')
def asd():
GPIO.output(led1,GPIO.HIGH)
buz.on()
while(1):
a=GPIO.Input(but1)
print a
if(a==1):
GPIO.output(led1,FALSE)
break
#---------------
GPIO.output(led2,GPIO.HIGH)#digitalWrite(led2,HIGH);
while(1):
b=GPIO.Input(but2)
if(b==1):
GPIO.output(led2,FALSE)
break
GPIO.output(led3,GPIO.HIGH)#digitalWrite(led3,HIGH);
while(1):
c=GPIO.Input(but3)
import RPi.GPIO as GPIO
GPIO.setmode(GPIO.BCM)
#make some values
pinNum = 17
self.isKilled = False
#set the pin
GPIO.setup(pinNum, GPIO.IN)
#grab the input
switch = GPIO.input(pinNum)
#check if the kill switch is pressed
while True:
if self.isKilled == False:
if (GPIO.Input(17)):
execFile(shutdown.sh)
self.isKilled = true
else:
return