Exemplo n.º 1
0
def countFails(scale, count):
    zeros = 0
    exceptions = 0

    drone1 = sensors.thermometer()
    drone2 = sensors.temperSensor()
    switch1 = switches.coolerSwitch()
    switch2 = switches.myX10('/dev/serial/by-id/usb-Prolific_Technology'
                             '_Inc._USB-Serial_Controller-if00-port0')
    switch3 = switches.pumpUSB()

    for x in range(0, count):

        try:
            d1 = drone1.getValue()
        except:
            sys.stdout.write('v')
        try:
            d2 = drone2.getValue()
        except:
            sys.stdout.write('t')
        try:
            s1 = switch1.off()
        except:
            sys.stdout.write('c')
        try:
            s2 = switch2.off()
        except:
            sys.stdout.write('x')
        try:
            s3 = switch3.off()
        except:
            sys.stdout.write('u')
        try:
            val = scale.getRaw()
            if int(val) == 0:
                zeros = zeros + 1
                sys.stdout.write("0")
            else:
                sys.stdout.write(".")
        except:
            exceptions = exceptions + 1
            sys.stdout.write("*")

        sys.stdout.flush()
        if x % 25 == 24:
            print ""

    print ""
    print "Exceptions:", exceptions
    print "Zeros     :", zeros
Exemplo n.º 2
0
def setupControllers(verbose, simulation, permissive, equipment):
    controllers = ctrl.controllerList()
    # The controllerinfo is a special snowflake that stores some extra global controller info
    # It does not do anything intelligent itherwise and will always meet target
    controllers.addController('controllerInfo', appliances.controllerinfo())
    
    if equipment is None:
        logging.error('Equipment is None')
        return(None)
    controllers['controllerInfo'].setEquipment(equipment)

    # Timer is always required in all equipment
    controllers.addController('delayTimer', appliances.hoptimer())

    print "Try to find hw switches"
    if not simulation:
        logging.info("Initializing hardware")
        x10 = None
        try:
            usbPumps = switches.pumpUSB()
        except:
            if permissive:
                logging.info("**********USB pumps not found, simulating HW")
                usbPumps = switches.simSwitchList()
            else:
                raise Exception("USB pumps not available")
    else:
        x10 = switches.simSwitchList()
        usbPumps = switches.simSwitchList()

    print("Setting up appliances")

    hwTunSwitch = switches.powerSwitch(1)
    boilerSwitch = switches.powerSwitch(2)
    print 0
    aeratorSwitch = switches.air8800Switch()
    print 0.2
    coolerSwitch = switches.coolerSwitch()
    mashStirSwitch = switches.mashStirSwitch()
    #mashStirSwitch = switches.mashStir8800Switch()
    print 0.5
    boilerValveSwitch = switches.boilerValveSwitch()
    hotWaterPumpSwitch = usbPumps.getSwitch(1)
    hwCirculationSwitch = usbPumps.getSwitch(0)
    wortSwitch = usbPumps.getSwitch(2)
    mashCirculationSwitch = usbPumps.getSwitch(3)
    print 1
    controllers.addController('waterHeater', appliances.hwt())
    controllers['waterHeater'].connectSwitch(hwTunSwitch)
    controllers['waterHeater'].setx(x10)

    controllers.addController('boiler', appliances.boiler())
    controllers['boiler'].connectSwitch(boilerSwitch)
    controllers['boiler'].setx(x10)

    controllers.addController('aerator', appliances.aerator())
    controllers['aerator'].connectSwitch(aeratorSwitch)
    print 2
    controllers.addController('cooler', appliances.cooler())
    controllers['cooler'].connectSwitch(coolerSwitch)
    boilerSensor = controllers['boiler'].getSensor()
    controllers['cooler'].connectSensor(boilerSensor)

    # Reuse of same switch for plate cooler as immersion cooler
    controllers.addController('plateValve', appliances.plateValve())
    controllers['plateValve'].connectSwitch(coolerSwitch)

    controllers.addController('mashStirrer', appliances.mashStirrer())
    controllers['mashStirrer'].connectSwitch(mashStirSwitch)
    controllers.addController('mashHeater', appliances.mashHeater())
    controllers['mashHeater'].connectSwitch(mashCirculationSwitch)
    print 5
    controllers.addController('boilerValve', appliances.boilerValve())
    controllers['boilerValve'].connectSwitch(boilerValveSwitch)
    controllers.addController('hotWaterPump', appliances.hwPump())
    controllers['hotWaterPump'].connectSwitch(hotWaterPumpSwitch)
    controllers.addController('waterCirculationPump',
                              appliances.circulationPump())
    controllers['waterCirculationPump'].connectSwitch(hwCirculationSwitch)
    controllers.addController('wortPump', appliances.wortPump())
    controllers['wortPump'].connectSwitch(wortSwitch)
    controllers.addController('boilerVolume', appliances.boilerVolume())
    controllers['boilerVolume'].attachHost(controllers['wortPump'])
    # controllers.addController('mashCirculationPump', \
    #                          appliances.circulationPump())
    # controllers['mashCirculationPump'].connectSwitch(mashCirculationSwitch)
    controllers.addController('dispenser1', appliances.dispenser(1))
    controllers.addController('dispenser2', appliances.dispenser(2))
    controllers.addController('dispenser3', appliances.dispenser(3))
    controllers.addController('dispenser4', appliances.dispenser(4))
    
    controllers.addController('envTemp', appliances.envTemp())

    print("appliance setup done")
    # Testing of sensor object Remove me later
    for key, c1 in controllers.items():
        c1.findOrAddSensor(controllers)
        # print key
    "returning..."
    return(controllers)